Interesting story, Ann. I'm assuming that these new pressure sensitive adhesives not only do a good job of sticking to the skin, but also go a long way in pain-free removal. Funny timing given that I just had a conversation with my 14-year son asking me to get some sort of special bandage that will stick to his skin, but won't hurt coming off to to dress the wounds he got from a recent longboard accident. Too bad the technology wasn't commercialized and already available in the local drug store!
Current Adhesive coverings for wounds cause major skin damage. My mom had some used on her in an operation she had. She had major skin lacerations 4 in by 6 in on either side of the operation. Because she had moved (minor moves) there were small cuts where the skin had torn in 1mm thin stripes alone the supporting strings in the strip of adhesive. It was painful for her and horrible image for the rest of us. Even with that risk supposedly wounds heal faster with adhesive strips supporting the wound.
This is a great idea. I won't have to use Super Glue on my kids' cuts any longer. In my lifetime there has only been one advance in home-based cut care -- Super Glue. It's good to see an advance that isn't as weird as Super Glue. Now if only they could come up with a home-based solution to putting a dental bridge back in place. My dentist doesn't recommend Super Glue, though she did say some of her patients have tried it.
Thanks for your input everyone. This material is designed for fragile skin undergoing major trauma: skin that is continually abraded by colostomy bag tubes, or open wounds, sometimes chronic ones, or skin that has recently been cut in surgery, for example. So not only does it stick easily, but it also removes easily. I'm sure it would work on more everyday minor wounds and cuts, although probably not on dental bridges.
A simple way to remove adhesive bandages painlessly, is to apply alcohol to the edge of the bandage with a cotton swab. The alchol will release the adhesive, and the bandage can be pulled away from the skin as you wipe the swab back and forth at the skin/bandage interface. If the cotton pad on the bandage has absorbed body fluid and is now stuck to the wound, salt water applied to the pad with an eye dropper will shortly soften the matrix holding the pad to the wound.
moha, thanks for your input. Using alcohol to remove adhesives from intact, uninjured skin definitely works. But your pain threshold must be a lot higher than mine: I would not put salt water anywhere near a wound. Also, there are coating cotton bandage materials with a slicker surface that are less likely to stick to a wound.
Moha, thanks for your valid input. I think most of us may come across such adhesive problems with bandage or cotton over the wound. Even I had struggled many times for removing these adhesive materials from skin and wound. Next time I will let you know whether it's effective or not.
The engineers and inventors of the post WWII period turned their attention to advancements in electronics, communication, and entertainment. Breakthrough inventions range from LEGOs and computer gaming to the integrated circuit and Ethernet -- a range of advancements that have little in common except they changed our lives.
The age of touch could soon come to an end. From smartphones and smartwatches, to home devices, to in-car infotainment systems, touch is no longer the primary user interface. Technology market leaders are driving a migration from touch to voice as a user interface.
Soft starter technology has become a way to mitigate startup stressors by moderating a motor’s voltage supply during the machine start-up phase, slowly ramping it up and effectively adjusting the machine’s load behavior to protect mechanical components.
A new report from the National Institute of Standards and Technology (NIST) makes a start on developing control schemes, process measurements, and modeling and simulation methods for powder bed fusion additive manufacturing.
If you’re developing a product with lots of sensors and no access to the power grid, then you’ll want to take note of a Design News Continuing Education Center class, “Designing Low Power Systems Using Battery and Energy Harvesting Energy Sources."
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.