HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  RESOURCE CENTER  |  INDUSTRIES
News
Materials & Assembly
Strong, Flexible Composite Combines Minerals, Thermoplastic
12/20/2012

Eovations's mineral/thermoplastic composite has a modulus of elasticity between 500,000 psi and 800,000 psi, but a modulus of rupture of zero. It can flex extremely well, but does not have a catastrophic failure mode.
(Source: Eovations)

Page 1/3  >  >>
User Rank
Platinum
Re: "The modulus of rupture is zero"
1/18/2013 5:22:53 PM
NO RATINGS
@Ann: Okay, apparently you learned some highly non-standard definitions.  According to Instron's glossary of materials testing, modulus of rupture is synonymous with flexural strength.  If you Google "modulus of rupture," you'll see that this is the most commonly used definition.  Clearly, "the flexural strength is zero" would not be a correct statement.

The derivation of the most widely-used modulus of rupture formula assumes that the material deforms in a linear and elastic way, so the formula no longer applies after the yield point.  However, this doesn't mean that "the modulus of rupture is zero"; it just means that the formula no longer correctly predicts the stress.

As far as "catastrophic failure" goes, the most common definition seems to be "(sudden) failure from which recovery is impossible."

Give me any material, and I guarantee I can find a way to make it fail such that you'll never get it back into its original shape.  Hit it hard enough, and it will fail catastrophically.

User Rank
Blogger
Re: Better wood than wood
1/18/2013 4:56:25 PM
NO RATINGS
I've also noticed that some earlier ideas and technologies are being revived,and given another chance. Some may have been inventions that were in advance of their time.

User Rank
Blogger
Re: "The modulus of rupture is zero"
1/18/2013 4:53:51 PM
NO RATINGS
Dave, I disagree. That's simply not the way I learned those definitions.

User Rank
Platinum
Re: "The modulus of rupture is zero"
1/18/2013 4:01:17 PM
NO RATINGS
@Ann: The fact that something bends before it breaks doesn't mean that it doesn't have a catastrophic failure mode -- it just means that it bends first.  If you continue to load it, it will fail catastrophically, sooner or later. (Steel bends before it breaks, too, but you can point to any number of catastrophic failures of steel structures).

And "the modulus of rupture is zero" is just plain wrong.  As I said, modulus of rupture is a measure of the load-carrying capacity of a beam.  If the load-carrying capacity were zero, it would be useless.

Modulus of rupture just isn't a useful number for something that yields before it breaks, since the equation assumes no yielding.

User Rank
Blogger
Re: Better wood than wood
1/4/2013 2:51:28 PM
NO RATINGS
Scott, this was originally developed at Dow but never commercialized, so I suspect it was not aimed at specific applications, at least originally.

User Rank
Blogger
Re: "The modulus of rupture is zero"
1/4/2013 12:38:58 PM
NO RATINGS
TJ, thanks for the clarification. Determining that would probably take a detailed lifecycle analysis. Although these are now voluntary, and not nearly as common as many of us would like, I hope that someday they'll be required as an item on the data sheet.

User Rank
Blogger
Re: "The modulus of rupture is zero"
1/3/2013 9:13:23 PM
NO RATINGS
The original question was worse for the environment - structural members made from wood or the composites described in the article.

The lumber industry sells itself as renewable because the companies plant trees to replace the ones harvested, and the renewal process is pretty straight forward - Cut down a forest, make lumber, plant seedlings in the now-cleared area, come back in 20 years or so and repeat.

IF the composites are made from organic feedstocks, they may be the equal of wood's impact on the environment.  If they're made from petrochemicals, one would probably have to say they have a larger impact.

User Rank
Blogger
Re: "The modulus of rupture is zero"
1/3/2013 8:10:22 PM
NO RATINGS
TJ, I'm still not getting your point. Organic feedstocks are at least potentially renewable, whether they're based on trees or on other plants.

User Rank
Blogger
Re: Better wood than wood
1/2/2013 12:05:48 PM
NO RATINGS
Lou, I thought the hurricane-resistance use was one of the most intriguing and unique about this material, aside from the more mundane uses like deck replacement. Chuck, this is not aimed at high load-bearing structural components such as bridge beams: as we state, it's for lighter construction uses such as decks and pontoons.

User Rank
Platinum
Re: Better wood than wood
12/30/2012 5:28:48 PM
NO RATINGS
Interesting development.  Nice to see these sort of efforts moving forward.  They may not always be the most cost effective, but it's a step in the right direction.  I wonder if this is one of those "we can do it in the lab, so let's see if we can sell it" sort of things or if they actually had a specific market in mind.

Page 1/3  >  >>
 Partner Zone
Latest Analysis
Nissan Motor Co. is taking the electric vehicle into new territory, rolling out an exotic-looking three-seat concept car that combines sustainability with race car-like performance.
3D visualization is helping us express information in a way that’s more informative and easier to decipher.
A new service lets engineers and orthopedic surgeons design and 3D print highly accurate, patient-specific, orthopedic medical implants made of metal -- without owning a 3D printer. Using free, downloadable software, users can import ASCII and binary .STL files, design the implant, and send an encrypted design file to a third-party manufacturer.
When Dick Neubert discovered that his fireplace's heatilators lost heat when not in use, he created a gadget to rectify the situation.
More:Blogs|News
From Dell / Intel®
Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013    7
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
Most recent post: Ralphy Boy
From Dell / Intel®
Trey Morton, Dell, 4/25/2013    3
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
Most recent post: Cabe Atwell
From Dell / Intel®
Kirsten Billhardt, Manufacturing Industry Marketing Strategist, Dell, 3/26/2013    6
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
Most recent post: Ockham
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Dec 16 - 20, Introduction to SCADA Security
SEMESTERS: 1  |  2  |  3  |  4