HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
Feature
Electronics & Test
Measure Efficiency Quickly in Switching Power Supplies
10/11/2013

Image 1 of 5      Next >

Figure 1. Phase angle between input voltage and current.

Image 1 of 5      Next >

User Rank
Gold
Considering the noise, as well
10/14/2013 8:33:36 PM
NO RATINGS
This is an interesting and useful posting. But sometimes the readings from a noisy supply will be inacurate because of the noise on top of the DC output, and possibly on top of the input as well. An easy solution is to add filtering and read the voltage outside the filters. Usually the output voltage will be different with the noise filtered out, either higher or lower. Likewise the current, although it will usually be lower. This does reflect that noisy supplies are not as good as quieter ones.

User Rank
Platinum
10/14/2013 11:06:32 AM
NO RATINGS
This article seems to ignore the fact that most (those without active PFC) AC-DC power supplies are non-linear loads, and therefore the traditional concept of power factor doesn't apply. Current drawn by a typical SMPS (like a computer power supply) is in phase with the voltage since the bulk filter caps charge at the peak of the voltage waveform. The resultant waveform is severly distorted however. This is not the case if the SMPS uses active power factor correction.

For non-linear loads, make sure to use a wattmeter designed to measure distorted waveforms. You can check for distortion by measuring the Crest Factor of the waveform using a DMM that has a peak capture mode and can measure true RMS. A pure sinewave will have a crest factor (Peak/RMS ratio) of 1.414. Any variation greater or lower indicates distortion. Typical SMPS current draw waveforms will have a very high crest factor, generally around 5. This indicates the typical "peaky" current waveform when caps charge at the peak of the voltage waveform. [voltage waveform distortion - especially in SMPS - tend to have crest factors less than 1.414 due to voltage flattopping]

An SMPS with active PFC will have sinusoidal (well, very nearly sinusoidal) voltage and current waveforms, and they will be in phase so input power is simply VrmsxIrms.

User Rank
Gold
Power supply efficiency
10/14/2013 9:25:15 AM
NO RATINGS
If you need a wattmeter, an excellent and economical choice is the Weston 310 series.  These are the "Lab Standard" instruments in the mahogany cases rated at 1/4% accruacy.  Since they are electrodynamometers they measure true watts and they have no permanent magnets that can change strength over time.  You can check their calibration with DC using an accurate voltmeter and ammeter on the potential and current terminals, respectively, but it is best to flip polarity to check both ways.

These instruments were very expensive when new (>\$1000), but are now available quite cheaply on the used market.  And they are real works of art.

User Rank
Blogger
Efficiency always
10/11/2013 10:48:49 AM
NO RATINGS
This is just one more example of increased efficiency in power supplier. It will be interesting to see the cumulative effect of efficiency gains in so many areas.

 Partner Zone
Latest Analysis
Days after a massive, distributed denial-of-service attack took down dozens of major websites around the country, ARM Holdings plc is rolling out a pair of new processor architectures aimed at shoring up IoT security.
Dow Chemical and several other companies have launched a program in Omaha, Neb. to divert about 36 tons of plastics from landfills in its first phase, and convert it into energy used for cement production.
Both traditional automation companies and startups are developing technologies to improve processes on the factory floor, while smart sensors and other IoT-related technologies are improving how products are handled during transport and across the supply chain.
Remote monitoring now looks beyond the individual motor or conveyor and instead views the process from end to end.
BASF is partnering with Hyundai on a high-performance concept car that showcases both eco-friendly, sustainable materials and materials to enable lighter weight cars.
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 10 - 14, Embedded System Design Techniques™: Getting Started Developing Professional Embedded Software
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course September 27-29: