HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Feature
Materials & Assembly
Device Manufacturers Embrace Electrically Conductive Adhesives
4/8/2013

Image 1 of 3      Next >

Image 1 of 3      Next >

Return to Article

View Comments: Newest First|Oldest First|Threaded View
JimT@Future-Product-Innovations
User Rank
Blogger
Hard Lesson Leaarned
JimT@Future-Product-Innovations   5/9/2013 6:36:05 PM
NO RATINGS
Looking back over archived stories, I had missed this one, now over a month old. I have several past product experiences using various conductive adhesives, and I had learned a very valuable lesson a few years ago. 

Without going into specifics, I can tell you I had designed myself into a corner, and needed to get an electrical component connected to the main circuit. Based on its unique mounting condition, a conductive adhesive was the obvious answer.  I simply plowed forward with the mounting method and the adhesive, and had first parts prototyped.

 When the component didn't function properly, I learned the current required for the component far exceeded the current capability of the conductive particles in the adhesive.  There was no way the adhesive as ever going to drive the component properly, and I was stuck.

This bad assumption kicked me back significantly, and I had to undergo a substantial redesign.  That's one lesson I'll never forget.

William K.
User Rank
Platinum
Re: Electrically conductive adhesives.
William K.   4/29/2013 10:11:57 PM
NO RATINGS
I do see a serious potential for use with surface mount components, particularly the very small ones with sizes under one mm. Those parts are a big challenge to work with by hand, which makes prototyping quite a challenge. A conductive adhesive could provide some help.

notarboca
User Rank
Gold
Re: Electrically conductive adhesives.
notarboca   4/29/2013 9:32:40 PM
NO RATINGS
This should be quite handy in electrically connecting components in situations too tight for a wire or traditional connector.

Greg M. Jung
User Rank
Platinum
Chemical Resistance
Greg M. Jung   4/11/2013 9:47:03 PM
NO RATINGS
Well researched article. I am assuming that the silicone in the adhesive can also help increase inadvertent exposure to chemicals and possibly have good chemical resistance.

William K.
User Rank
Platinum
Electrically conductive adhesives.
William K.   4/9/2013 11:29:36 AM
NO RATINGS
It is clear that stable electrically conductive adhesives can be of great value in quite a few applications. So the usefulness potential is quite high.

Mant years ago I had an experience with anelectrically conductive adhesive material that I used to assemble a switch. The problem was that I did not realize that the material was conductive at all. The result was that while the assembly was fine mechanically, the switch was always "on", which caused me quite a bit of puzzelment, since it was clear that the contacts were opening as desired. The end result was that I had to use a different switch and a mechanical means of attachment. But it was certainly an educational experience.

Partner Zone
Latest Analysis
The engineers and inventors of the post WWII period turned their attention to advancements in electronics, communication, and entertainment. Breakthrough inventions range from LEGOs and computer gaming to the integrated circuit and Ethernet -- a range of advancements that have little in common except they changed our lives.
The age of touch could soon come to an end. From smartphones and smartwatches, to home devices, to in-car infotainment systems, touch is no longer the primary user interface. Technology market leaders are driving a migration from touch to voice as a user interface.
Soft starter technology has become a way to mitigate startup stressors by moderating a motor’s voltage supply during the machine start-up phase, slowly ramping it up and effectively adjusting the machine’s load behavior to protect mechanical components.
A new report from the National Institute of Standards and Technology (NIST) makes a start on developing control schemes, process measurements, and modeling and simulation methods for powder bed fusion additive manufacturing.
If you’re developing a product with lots of sensors and no access to the power grid, then you’ll want to take note of a Design News Continuing Education Center class, “Designing Low Power Systems Using Battery and Energy Harvesting Energy Sources."
More:Blogs|News
Design News Webinar Series
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
5/7/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
May 4 - 8, Designing Low Power Systems using Battery and Energy Harvesting Energy Sources
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service