To provide more flexibility in charging mobile systems, designers are creating methods such as wireless and solar charging, but their challenges don't end there; they must also be concerned about environmental and safety issues related to charging. Wireless and solar charging are excellent topics, but we will narrow the focus to environmental and safety concerns caused by charging mobile devices. Fortunately, those issues can be addressed with a range of innovative ICs that provide connection, protection, and detection.
Protection
Protection not only applies to protection of the system but extends to environmental protection by reducing electronic waste. For example, when a cellphone user gets a new phone and disposes of an old one, the charger normally goes to the dump with it. In fact, nearly a billion phones and their attendant chargers are being discarded each year, thus populating landfills. If chargers could be transferred from one phone to the next (i.e., be universal), a more environmentally friendly situation would arise to reduce this wasteful practice.
A Korean 20-pin TTA charger.
Fortunately, that is exactly what is starting to happen across the globe. The European Commission has proposed a memorandum of understanding to harmonize chargers, which is driving phone manufacturers to use micro-USB connections on chargers for data-enabled smartphones (the fastest-growing tier). Chargers can therefore be used from phone to phone and generation to generation. In the US, to promote a greener world, major cellphone suppliers are joining with cellphone chipset producers, service providers, and two US wireless trade associations -- the GSMA and CTIA -- to push the Universal Charging Solution (UCS) initiative. The Telecommunications Technology Association (TTA) of Korea has recognized the advantages of reusable charging solutions for some time and has approved a universal 20-pin connector for chargers and earphones to address slimmer phone profiles than the former 24-pin connector could (see photo above).
Regarding safety concerns, China has taken a universal approach that also uses the USB port. Safety concerns have grown because the notion of cellphone batteries exploding is unnerving to say the least. High-profile reports of injuries in China have prompted the Chinese Ministry of Information Industry to issue its Technical Requirements and Test Method of Charger and Interface for Mobile Telecommunication Terminal Equipment to promote charging safety.
Overvoltage protection
A key element of the Chinese and other safety standards relates to protection from overvoltage conditions, which, as the name implies, is when the voltage used to recharge a battery is higher than a specified safe level for that particular battery. Overvoltage can damage a battery even to the point of catching fire, so overvoltage protection (OVP) integrated circuits are designed to ameliorate such concerns. OVP ICs monitor the voltage and isolate the phone from the charging source if the voltage gets too high. Typical OVP ICs contain internal MOSFETs or control one or more external MOSFETs to switch off the offending charging source. They are a simple, cheap, and effective way to enhance safety.
Because space is always at a premium in a cellphone, a compact package is necessary, and being battery-powered, a low power drain is mandatory. The Korean application, as an example, requires the protection IC to be in-circuit at all times and protect the handset against ±20V. Also, the device must be bidirectional, passing the battery voltage back to the device for USB On-the-Go (OTG) detection. To comply with Korean standards, triggering should be set at a battery voltage of 4.35 with ±1 percent tolerance. Other places have slightly different requirements, so there should be constant attention to the particulars.
These all should be the standard set of design requirements in any project. When this the basics start getting overlooked?
The problem with standardizing the power connection is not about the charging, but its use as a communication port as well. As data demands start surpassing the port's bandwidth, the connector has to change. USB 3.0 has the potential to be the next universal plug, but that may get outstripped as HD content demands increase.
So, don't expect a universal standard any time soon.
I agree, Greg. It's great to read an article about cooperation with something that seems so obvious yet has not been implemented in the past, I am guessing because companies wanted to maintain control and therefore the profit of their own chargers. Over voltage protection is a common engineering practice for a well-designed circuit and universal chargers just make so much more sense!
There was movement in the past to require by law that all chargers had the same power connector. Several years later, they are not. But many companies as joined together to standardize the port. Like all standardizations, have common ground will help a lot of companies make new products. Especially when that standard is free to use. Open that up, and everyone will hop on board. But like Moore's law demands doubling of processing power, so follows the communication ports.
I think the best way to go on this subject is wireless charging and data communication. Look at the company Witricity, they are trying to push a magnetic resonance charging system that has little loss over sizable distances. It looks very promising, and shows the what is next.
No kidding, since nearly every phone has some sit of USB connector, why can,t that serve as the charger port? Yes, this means some sort of charge in the phone, but it could be a featureless charge that just got a few electrons into the battery.
Great idea to commonize chargers and require manufacturers to meet more universal standards. Hopefully, this will not only result in less landfill waste, but also increased safety across the entire product spectrum.
UK-based Plastic Logic and French company ISORG have created what the pair tout as a first in flexible printed electronics: a large area, conformable, organic image sensor printed on plastic.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
1 
