HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Feature
Materials & Assembly

Converting Machined Parts to Die Castings

NO RATINGS
Page 1 / 3 Next >
View Comments: Newest First|Oldest First|Threaded View
Greg M. Jung
User Rank
Platinum
Die Casting
Greg M. Jung   9/15/2012 3:36:50 PM
NO RATINGS
I agree that converting machined parts to die casting usually makes sense.  Because die casting tools can be expensive, it is important to first do a pay-back analysis and see if the volumes justify this change over.

In many cases we use both processes during the life of the product.  When the initial design is likely to change and we need to enter the market quickly, we may start with a machined part.  Then, as the design becomes stable and production volumes increase, we plan for a smooth cut-over to die cast tooling.

 

Dave Palmer
User Rank
Platinum
Comparing processes
Dave Palmer   8/6/2012 12:31:33 PM
NO RATINGS
In most cases, casting a part versus machining it from bar stock is a no-brainer.  In my career, I've only come across one part that made more sense as a screw-machined part than as a die casting.  In that case, the geometry of the part made it extremely easy to screw machine.  Also, screw machining allowed the part to be made out of a much stronger wrought alloy.  It wound up being an 80% cost savings (from $4 to about 80¢), along with a more than 50% increase in strength.

But this is far from the norm, and as this article shows, casting is almost always much cheaper.  A more interesting comparison would be between die casting and powder metallurgy.  It would also be worthwhile to compare different casting processes (die casting, semi-solid processing, permanent mold, investment casting, lost foam, etc.).  In addition to cost, these processes also vary in terms of the mechanical properties and dimensional accuracy that can be achieved.

Partner Zone
Latest Analysis
It took engineers nearly half a century to determine why the SS Schenectady, while docked quietly in a harbor off Portland, Ore. one day, suddenly snapped in half.
The medical devices behind the superbug outbreak at UCLA suffer from a design flaw that experts have been aware of for decades.
Just when you thought mobile technology couldn’t get any more personal, Procter & Gamble have come up with a way to put your mobile where your mouth is, in the form of a Bluetooth 4.0 connected toothbrush.
The grab bag of plastic and rubber materials featured in this new product slideshow are aimed at lighting applications or automotive uses. The rest are for a wide variety of industries, including aerospace, oil & gas, RF and radar, automotive, building materials, and more.
Made By Monkeys highlights products that somehow slipped by the QC cops.
More:Blogs|News
Design News Webinar Series
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
11/19/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Mar 9 - 13, Implementing Motor Control Designs with MCUs and FPGAs: An Introduction and Update
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service