The concept of energy harvesting
At the core of self-powered wireless sensors and switches are energy-harvesting technologies. The principles of harvesting energy, whether solar, wind, or water, have been used for decades, but self-powered, batteryless technology was developed only 10 years ago. For instance, EnOcean developed an energy-harvesting model from the concept that sufficient ambient energy exists to power sensors and radio communications.
When it comes to networking a wide range of sensors, switches, and devices, calculating the required cabling and then installing it is often an organizational challenge that requires a great deal of effort and money to get right. However, it is a challenge that energy-harvesting wireless technology has resolved. These wireless modules take the power they need to work from the environment around them -- from motion, light, or changes in temperature. Instead of batteries, energy-harvesting-centric controls use miniaturized energy converters to supply power to building energy management devices. Even the action of pushing a light switch gives sufficient energy to generate a wireless signal and switch the light on. The technology provides enough energy to transmit and receive radio signals between controls and sustain vital communications within an energy management system.
At the center of energy harvesting and wireless is the EnOcean wireless standard. The messages sent by this wireless system are brief and repeated several times within a 40-millisecond timeframe. By transmitting these data packets at random intervals, it is possible to ensure that the probability of collision is extremely small. As a result, it is effortless to operate a range of switches and sensors in close proximity to one another. Each module has a 32-bit identification number to exclude any possibility of overlap with other wireless devices. The products are available in both 315MHz (for North America) and 868MHz (for Europe).
Implementing a wireless energy-harvesting system
The BAS reduces energy consumption in buildings on average 40 percent when smart sensors and controls are in place. However, most buildings still do not contain the controls necessary for managing energy, nor do they contain the cabling infrastructure needed to connect the essential sensors and controls. Widespread integration of building automation systems has been hindered by several factors. For instance, buildings have been expensive to retrofit (installation costs, slow payback, complicated installations), and interoperability between devices has been limited.
These classic barriers have been overcome by an ecosystem of energy-harvesting wireless controls that power themselves using energy infinitely available in building spaces.
I see energy harvesting more and more in uC controlled, wirelessly connected industrial sensors and networks. There are also a lot of protocols for wireless connectivity (WiFi, Zigbee, etc.) that may help early adoption of this technology.
Agree. The ability to provide energy based on the actuation a device is quite interested. By pressing a button on a typical electric switch, packets of data can be transmitted to a near by receiver and its powered using the same mechanical action. The concept of Energy Harvesting seems like sci-fi but EnOcean has made it into reality. Truly amazing.
Interesting technology and just more evidence that wireless designs and automation are going to make a big impact in the years ahead, eliminating cabling and increasing the convenience and flexibility of systems.
misdirection of antiquated data processing instrumentation to provide better security for the status quo---metrology should play an important key in elevating design for functionality, as architecture, also designs for functionality where we would be living mostly below frostline, while saving on heating and cooling costs, paying for itself in a short time. We do everything all wrong, an extension of the academic caste system used to devide the classes, in all modes of living dictated into the pseudo-educational system, mostly
The EnOcean products are another forward step in ISA (Integrated Systems Automation) offered over the past several decades by little know companys to early adopter's such as military, government, commercial building owners, etc. The key however, to successful use of these emerging technology products is their installation by qualified and properly trained people.
This being said a user is well advised to check out the install contractor. The systems only work "as advertised" if properly installed, and may cause serious damage due to failure. To prevent this parallel or human overides should be considered upon installation and use.
The government wants to study your brain, and DARPA wants to use similar information to give robots true autonomy beyond any artificial intelligence developed to date. Sound like science fiction? It's not.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
