HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Feature
Electronics & Test

Measure Efficiency Quickly in Switching Power Supplies

NO RATINGS
1 saves
Page 1 / 3 Next >
View Comments: Threaded|Newest First|Oldest First
Rob Spiegel
User Rank
Blogger
Efficiency always
Rob Spiegel   10/11/2013 10:48:49 AM
NO RATINGS
This is just one more example of increased efficiency in power supplier. It will be interesting to see the cumulative effect of efficiency gains in so many areas.

j-allen
User Rank
Gold
Power supply efficiency
j-allen   10/14/2013 9:25:15 AM
NO RATINGS
If you need a wattmeter, an excellent and economical choice is the Weston 310 series.  These are the "Lab Standard" instruments in the mahogany cases rated at 1/4% accruacy.  Since they are electrodynamometers they measure true watts and they have no permanent magnets that can change strength over time.  You can check their calibration with DC using an accurate voltmeter and ammeter on the potential and current terminals, respectively, but it is best to flip polarity to check both ways.  

These instruments were very expensive when new (>$1000), but are now available quite cheaply on the used market.  And they are real works of art. 

ChuckMahoney
User Rank
Gold
non linear loads
ChuckMahoney   10/14/2013 11:06:32 AM
NO RATINGS
This article seems to ignore the fact that most (those without active PFC) AC-DC power supplies are non-linear loads, and therefore the traditional concept of power factor doesn't apply. Current drawn by a typical SMPS (like a computer power supply) is in phase with the voltage since the bulk filter caps charge at the peak of the voltage waveform. The resultant waveform is severly distorted however. This is not the case if the SMPS uses active power factor correction. 

For non-linear loads, make sure to use a wattmeter designed to measure distorted waveforms. You can check for distortion by measuring the Crest Factor of the waveform using a DMM that has a peak capture mode and can measure true RMS. A pure sinewave will have a crest factor (Peak/RMS ratio) of 1.414. Any variation greater or lower indicates distortion. Typical SMPS current draw waveforms will have a very high crest factor, generally around 5. This indicates the typical "peaky" current waveform when caps charge at the peak of the voltage waveform. [voltage waveform distortion - especially in SMPS - tend to have crest factors less than 1.414 due to voltage flattopping]

An SMPS with active PFC will have sinusoidal (well, very nearly sinusoidal) voltage and current waveforms, and they will be in phase so input power is simply VrmsxIrms.

William K.
User Rank
Platinum
Considering the noise, as well
William K.   10/14/2013 8:33:36 PM
NO RATINGS
This is an interesting and useful posting. But sometimes the readings from a noisy supply will be inacurate because of the noise on top of the DC output, and possibly on top of the input as well. An easy solution is to add filtering and read the voltage outside the filters. Usually the output voltage will be different with the noise filtered out, either higher or lower. Likewise the current, although it will usually be lower. This does reflect that noisy supplies are not as good as quieter ones.

Partner Zone
Latest Analysis
Some humanoid walking robots are also good at running, balancing, and coordinated movements in group settings. Several of our sports robots have won regional or worldwide acclaim in the RoboCup soccer World Cup, or FIRST Robotics competitions. Others include the world's first hockey-playing robot and a trash-talking Scrabble player.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Melissa Cavanagh of 3DP Unlimited talked to Design News about the company’s large format 3D printer, during Medical Design and Manufacturing Midwest.
The DDV-IP is a two-wheeled self-balancing robot that can deliver cold beverages to thirsty folks on hot summer days. A wireless RF remote enables manual control of the device beyond the act of self-balancing. All of the features of the DDV-IP result in an effective delivery vehicle while providing entertainment to the user.
Eric Doster of iFixit talks about the most surprising aspect of the Microsoft Surface Pro 3 teardown. In a presentation at Medical Design & Manufacturing Midwest, iFixit gave the Surface Pro 3 a score of one (out of a possible 10) for repairability.
More:Blogs|News
Design News Webinar Series
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 20 - 24, How to Design & Build an Embedded Web Server: An Embedded TCP/IP Tutorial
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: 10/28-10/30 11:00 AM
Sponsored by Stratasys
Next Class: 10/28-10/30 2:00 PM
Sponsored by Gates Corporation
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service