HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Feature
Automation & Motion Control

Bottles Up

NO RATINGS
Page 1 / 2 Next >
View Comments: Newest First|Oldest First|Threaded View
Ann R. Thryft
User Rank
Blogger
Re: Plastic bearings instead of metal bearings.
Ann R. Thryft   8/21/2013 8:04:21 PM
NO RATINGS
Another place these plastic bearings are being used is in a concept car, the Personal Transport Vehicle by Redbud Technology
http://www.redbudtechnologyllc.com/3.html
according to an igus press release I just saw here
http://igus.com/Corporate/Press/5536/student-built-personal-transport-vehicle-uses-plastic-bearings

Cabe Atwell
User Rank
Blogger
Re: Plastic bearings instead of metal bearings.
Cabe Atwell   7/31/2013 7:21:59 PM
NO RATINGS
Cost effective, robust and easy to manufacture? What's not to like but like, however I agree with William in that it depends on the application as well as the environment on which type of bearing works best.

William K.
User Rank
Platinum
Plastic bearings instead of metal bearings.
William K.   7/1/2013 7:54:26 PM
NO RATINGS
Plastic bearings do offer very real advantages in some applications, but it is absolutely vital to assure that the bearing selected is adequate for the application. Of course, that is true with all bearing types, but sometimes the failure of an incorrectly applied plastic bearing can be quite impressive, even spectacular. So just as with other types of bearings, the application is not a trivial matter. The correct selection will assure satisfactory performance. 

The resistance to water and other liquids that are quite hard on regular bearings can be a very big benefit.

bobjengr
User Rank
Platinum
BOTTLES UP
bobjengr   7/1/2013 4:26:16 PM
NO RATINGS
  

Very informative post Michael.  One of the most difficult consulting jobs I have ever had was specifying bearings for conveyors used in a chain of bakeries. The issue was sugar granules getting into the bearing components and creating a remarkably short bearing life.  Sealed bearings did not seem to do the job adequately.   For this one department, I did specify a polymer.    That saved the day.  Again, very good post. Good information.

56ml
User Rank
Iron
Bushings
56ml   7/1/2013 9:57:51 AM
NO RATINGS
I've used Igus.  They are plastic bushings, which is as good as traditionsal bearings in some applications.  That's why there was a comparison with bronze "bearings" in the article.

Nancy Golden
User Rank
Platinum
cost comparison
Nancy Golden   6/30/2013 4:42:35 PM
NO RATINGS
This is a very interesting article on plastic ball bearings...from what I understand they are also lighter and quieter than other types. I wonder what the cost comparison is regarding steel or ceramic ball bearings but you would also have to factor in the plastic bearings comparitively lower maintenance and longer expected cycles into the equation...

Greg M. Jung
User Rank
Platinum
No Lubrication
Greg M. Jung   6/29/2013 7:55:46 PM
NO RATINGS
No lubrication needed with these types of bearings is a key feature.  Dust and contaminates will eventually settle on the operating surfaces and cause performance degradation.  This feature (along with preventing food contamination) is an important advantage with this product over lubricated bearings.

Partner Zone
Latest Analysis
National Instruments sees 5G WiFi and software-enhanced test equipment as advances that will change technology and business.
The new $120,000 Model S P85D boasts a 221-horsepower front motor and a 470-horsepower rear motor that packs a punch. The car is able to go from 0-60 MPH in just 3.1 seconds … quietly.
The new composites manufacturing innovation center is intended to be a source of grand challenges for industry, like the kind that got us to the moon under JFK. These aren't the words its new CEO Craig Blue used, but that's the idea and the vision behind the Institute for Advanced Composites Manufacturing Innovation (IACMI).
The ideal gas law, first stated in 1834, has suddenly become big news.
Bill Gates took to Reddit for an AMA (Ask Me Anything) and fielded fielded questions on everything from his outlook on the future of technology to who he's rooting for in the Super Bowl.
More:Blogs|News
Design News Webinar Series
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
11/19/2014 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jan 26 - 30, IPv6 for Micros – Hands-On
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Stratasys
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service