Nevermind all the talk of fuel efficiency mandates. Judging by product rollouts at recent auto shows, some consumers still want racy, stylish cars. And automakers aren't hesitating to build them.
Call them dream cars. Chevrolet launched one at the North American International Auto Show in January: Its powerful new 2014 Corvette Stingray. Not to be outdone, McLaren Automotive rolled out the new hybrid P1, and Lamborghini introduced the high-powered Veneno at this week's Geneva Motor Show.
We call them dream cars for good reason. The 2014 Stingray is rumored to have an expected pricetag of $55,000, which is dreamy enough. But the McLaren P1 -- with only 375 units in production -- will run $1.15 million. And the Veneno -- possibly the ultimate in automotive exclusivity -- will cost $3.9 million. Only three will be built.
We've put together a few facts and photos of the Stingray, Veneno, and P1, the better to feed consumer fantasies. Click on the photo to begin dreaming ...
The $3.9M Lamborghini Veneno features a 6.5-liter, 12-cylinder engine. Working with a seven-speed transmission, it produces 750 HP and accelerates from zero to 100 km/h in just 2.8 seconds. (Source: Automobili Lamborghini)
Simple , 80 mpg, light, .. sure people want these things but after all the manufacturers make cars that meet these simple requirements.. they will want safety, power , handling, excitement for only $5K!
Otherwise , what is will differentiate one car from the next? or do you think we should all have brown shoes?
The automotive industry pays big bucks to to find what will sell. And they haven't found a single solution for all mankind... they compromise and produce multiple solutions with the technology they currently have.
I like the idea there is a place in the world for exotics.. on one thinks they will work for the masses.. and that is OK.
Dang! I think 26 mpg , 0-60 in 4 seconds, 1G side load.. addresses a lot of compromises.
Chuck, Thanks for the slideshow and we can sense your enthusiasm for dream car designs and new technologies. Even given the most frugal approach to efficiency and practicality, there will always be a place for dream cars in the automotive landscape. Thanks.
The article said that these expensive cars appearing at car shows indicates customers want them, and that is not true.
Car show presentations are what makers want to sell, not what consumers want to buy. Consumers want 80 mpg car that are simple, light, and easy to maintain. It is just that car makers don't want to sell them that, because there is not as much profit margin on them.
In 1970 Pontiac GTO had a very short lived option similiar to the Stingray exhaust option shown on slide 17. Back in the day you could get a vacuum operated exhaust for the GTO. You pull the lever and valves in the muffler would open up and reduce the back pressure and up the coolness sound of the V8. I even think that you can purchase this system as a reproduction today!
So what sounds like a new design idea for a stock car (I know racers have done this for years), it is nothing new. $55K for the Stingray, or $1.5million for the other, or 3.9 million for one of the three. Not sure which one to get?
Cap'n, that Laambo is really wild. Actually all of thier cars are, but this one is really out there. That rear view is what prompted the subject of this post. Cool stuff.
I like all the cars you show, but the Stingray is really nice and I want one.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
6 
