In an effort to make streets safer for pedestrians, the National Highway Traffic Administration (NHTSA) has proposed a rule that could require engineers to add more sound to hybrids and electric vehicles (EVs).
The proposed rule, a follow-on to the Pedestrian Safety Enhancement Act of 2010, would likely require that automakers add external speakers to hybrids and EVs. NHTSA estimates that such speaker systems would add about $30 to the manufacturing cost of the cars, but could prevent about 2,800 injuries over the life of each vehicle model year.
"Our proposal would allow manufacturers the flexibility to design different sounds for different makes and models while still providing an opportunity for pedestrians, bicyclists, and the visually impaired to detect and recognize a vehicle and make a decision about whether it's safe to cross the street," NHTSA administrator David Strickland said in a press release.
Toyota's Prius uses a Vehicle Proximity Notification System under the hood that emits additional engine-like noises below 15mph. (Source: Toyota)
The mandate is the result of numerous studies over the past five years that have shown that the incidence of pedestrian crashes is higher among hybrids and electric cars. A 2009 study from NHTSA conducted on 8,287 hybrids and 559,703 conventional vehicles showed that hybrids were "two times more likely to be involved in a pedestrian crash." Similarly, a study done in Japan at the request of the Japanese Federation of the Blind revealed that more than half the blind respondents were "terrified" of hybrids.
NHTSA's mandate would provide leeway for automakers as to the kinds of sounds, but it does call for them to be detectable under a wide range of street noises and ambient background sounds.
Some hybrids and EVs already incorporate mechanisms for additional sound. Toyota's Prius and RAV EV vehicles, for example, employ a Vehicle Proximity Notification System (VPNS), which is located under the hood and emits sounds at speeds under 15mph. VPNS includes low- and high-frequency sounds that mimic Toyota's internal combustion engines. "It's a retrofitted little speaker behind the front grille," Jana Hartline of Toyota told Design News. "It's not anything that can be heard inside the car, but it is distinctive."
NHTSA said it will give the public 60 days to comment on the proposed mandate. Automakers are expected to work with the agency on the development of a standard. "We've studied it on our own and we will continue to work with NHTSA on it," Hartline said.
I average 18mph (burst of up to 30mph) on a7 mile ride and I have never been unable to hear approaching cars from behind. Do I trust my ears alone? No. But I've never been surprised by Prius, Volt, Tesla Roadster, or any other hybrid or electric vehicles. In biking events or on bike paths I can even hear approaching bicycles from behind (bike chain, wind, and tire noise). So I'm surprised that wind noise overpowers car noises for you.
It's been interesting to see all the comments about this! Obviously it's struck a nerve...and danger aside, I'm happy to see a number of people less than thrilled about the idea of noisier hybrids and EVs. There has to be a better solution.
The Locomotive Acts (or Red Flag Acts) were a series of Acts of Parliament in the United Kingdom to control the use of mechanically propelled vehicles on British public highways during the latter part of the 19th century.
...
The 1865 act required all road locomotives, which included automobiles, to travel at a maximum of 4 mph (6 km/h) in the country and 2 mph (3 km/h) in towns and have a crew of three travel, one of whom should carry a red flag walking 60 yards (55 m) ahead of each vehicle.
Backup audible warning is already implemented on most trucks, commercial vehicles, municipal vehicles, etc. That is not a bad idea; the driver has limited view, and risk is higher. But that is totally different than always on noise generators.
Extra: Noun: An item in addition to what is usual or strictly necessary.
If you have to add the noise to an EV or Hybrid, it is extra. The world is way too noisy today.
While they are at it, why not ban wearing earbuds, headphones, hats covering the ears, earplugs, earmuffs, or anything else which reduces the auditory acuity of pedestrians?
We have too many rules, too many regulations, too many laws.
I support a rule requiring EV drivers to crank their stereos below 15 mph. Would be easy to implement in the electronics already there, and cost nothing.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
