HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Product News
Mechatronics

Video: ST Robotics' 11-Axis Tandem Robot System

NO RATINGS
View Comments: Newest First|Oldest First|Threaded View
Ann R. Thryft
User Rank
Blogger
Re: eleven axis robotic system
Ann R. Thryft   11/15/2012 4:51:17 PM
NO RATINGS
William, thanks for giving us a description of that incident: very scary, indeed. I can see why there's so much concern about careful industrial robotics programming.

William K.
User Rank
Platinum
Re: eleven axis robotic system
William K.   11/5/2012 7:53:59 PM
NO RATINGS
The reason thatbthings seem to be different in production is that the robots move much faster than during any of the setup modes, and also that (it seems), the production staff tend to run robots toward their maximum capabilities. The very exciting experience that I had was a robot that I had done the path programming for flinging a six-pound transmission part across the work area. Fortunately we were not yet in a production mode, and the part harmlessly hit the floor twenty feet away. But it certainly could have ruined sombody's day. That incident was the result of the production motion speed being set much faster than it needed to be, and the gripper air pressure being lower than it should have been set at.

Rob Spiegel
User Rank
Blogger
Re: eleven axis robotic system
Rob Spiegel   11/5/2012 2:23:53 PM
NO RATINGS
Interesting, William. Why would the robot's performance be different in production? Does it have to do with the weight or resistance the robot encounters in production?

William K.
User Rank
Platinum
eleven axis robotic system
William K.   11/5/2012 10:46:49 AM
NO RATINGS
In theory at least it should not be that very difficult to link the two robots into one robotic program. Putting two 5-axis robots on a common base is an interesting concept, and it does reduce the concerns that would exist using two six-axis robots side by side. One thing that ceratinly will require a bit of extra attention is the much greater inertia encountered when swinging the common axis. Inertia is one of those things that tends to "get in the way" when programming robotic motions. Things that work perfectly at setup speeds suddenly have problems when running at production speeds. This is most obvious when grippers are unable to hold the part securly during high speed changes in direction. The result can be a part weighing several pounds being thrown quite a few feet.

mrdon
User Rank
Gold
Re: Cool robot
mrdon   11/3/2012 10:34:49 PM
NO RATINGS
Hi Rob, I agree. The movement of the 2 robotic arms are very impressive. I thought the Dremel added a nice touch to the versatility of tools that can be attached to it. I wonder what robotic system is more cost competitive, ReThink Robotics "Baxter" or the ST Robotics Tandem Robot System? Very cool video!!

Rob Spiegel
User Rank
Blogger
Cool robot
Rob Spiegel   11/2/2012 2:10:06 PM
NO RATINGS
That's a pretty cool video. It really shows the value of the robot. It's nice to see prices coming down on this type of equipment -- a boon for small manufacturers. 

Partner Zone
Latest Analysis
We searched far and wide for the top employers for engineers. These companies were ranked by engineering professionals, engineering students, and engineering instructors and professors. Does your employer make the grade?
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
While every company might have their own solution for PLM, Aras Innovator 10 intends to make PLM easier for all company sizes through its customization. The program is also not resource intensive, which allows it to be appropriated for any use. Some have even linked it to the Raspberry Pi.
The demand for solar energy around the world will grow a total of 75% by 2019, according to a new report by Lux Research. Trade disputes and policy changes, though, will complicate the picture.
Using a 3D printer, CNC router, and existing powertrain components, a team of engineers is building an electric car from scratch on the floor of the International Manufacturing Technology Show in Chicago this week.
More:Blogs|News
Design News Webinar Series
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Sep 22 - 26, MCU Software Development A Step-by-Step Guide (Using a Real Eval Board)
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: September 30 - October 2
Sponsored by Altera
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service