Wood and pulp giant Weyerhaeuser says it has figured out how to make a thermoplastic composite using engineered cellulose fiber from trees, instead of the short glass fibers usually used for reinforcement. Applications for the material include automotive parts and industrial components.
The composite, called THRIVE, is targeted at low-load applications such as office furniture, consumer appliances, kitchenware, and household goods, in addition to car parts. According to the company, compared to composites made with short glass fibers, or natural fibers like sisal, hemp, and kenaf, the new material has several advantages.
A new thermoplastic composite uses engineered cellulose fiber from trees, such as these logs in Kuopio, Finland, instead of the short glass fibers usually used for reinforcement. Applications include automotive parts and industrial components. (Source: Wikimedia Commons/Okko Pyykkö)
Injection-molding cycle times are up to 40 percent shorter than composites made with glass fibers, since the new material requires shorter pack-and-hold and cooling times. Mass is also reduced, since cellulose fiber is 40 percent less dense. Finished parts are up to 8 percent lighter. Short glass fibers are highly abrasive and hard on processing equipment, so cellulose fiber composites can reduce wear and tear. The composite's mechanical properties are similar, including tensile strength and flexural strength.
Several different composites have been made with natural fibers, including coconut fibers instead of traditional ceramic fibers in biocomposite tiles. The natural fibers improve the composite's strength and stiffness, and reduce their weight. Compared to an engineered material such as THRIVE, composites made with natural fibers can vary in quality from one batch to another. They also don't readily absorb dyes. In contrast, the new material easily absorbs dyes and demonstrates consistent performance characteristics between batches.
"THRIVE products offer excellent flowability and thin-section fill, providing manufacturers with considerable design flexibility," says Don Atkinson, Vice President, Marketing and New Products for Weyerhaeuser's Cellulose Fibers business, in a press release. He goes on to say:
In addition, THRIVE composites are produced using a proprietary process that allows control of the dispersion of cellulose fibers within the polymer matrix. This allows for a smooth surface finish, which opens up new opportunities for the use of natural fibers in composite plastics. Conversely, if manufacturers prefer the fibers to be visible, they have that option as well."
The cellulose fiber is sourced partly from some of Weyerhaeuser's 20 million acres of forestland, which the company manages to third-party sustainability standards. Weyerhaeuser expects to produce the composite using its pulp manufacturing facilities. The material is provided as cellulose blended with polypropylene, with both high and low melt flow indices. It is available in both ready-to-mold thermoplastic pellets for molders, and in a masterbatch form for custom compounders.
The ratio of cellulose fiber to polymer in the composite can be changed to modify product strength and flexibility. From 10 percent to 40 percent, THRIVE cellulose fibers can be pre-blended with 60 percent to 90 percent of either virgin or pre-consumer recycled polypropylene. (Pre-consumer recycled is after manufacture but without consumer use, such as manufacturing waste byproducts.) The fibers can also be blended with ABS, PVC, low-density polyethylene (LDPE), high-density polyethylene (HDPE), or PLA and other biopolymers. Weyerhaeuser says it plans to expand the THRIVE line of products beyond polypropylene to include hydrocarbon and nonhydrocarbon polymers.
Jerry, that poly-cotton mix sounds like what I liked best for hiking clothes in my backpacking days. Cotton was supposed to be a no-no among backpacking enthusiasts because it takes so long to dry, either when wearing it, or when washing it at the campsite. But I found 100% polyester and other non-natural clothing to be too hot and sticky for comfort, no matter how it was made.
Just as bad is it melting on the skin then when you slap it to put it out it sticks to the hand and spreads sticking to the skin where it was buring/melting. Not a good way to go.
Living in Fla pure polyster is just too hot and uncomfortable in the summer. Though I really like rayon which is about the most comfortable cloth usually, slightly better than cotton and doesn't seem as flamable as polyester or nylon. A good 65% cotton, 35% polyster works fairly well and cuts the problems of pure cotton or pure poly.
That's an interesting story about polyester vs cotton and the flammability of natural vs synthetic materials. I remember as a kid in the 50s-60s hearing about the flammability of synthetic clothing material, which, I believe, is when many of the standards were developed for clothing material flammability.
Sounds like a waste product they are trying to find a use for. From the specs it's rreally just a filler pounded into dust so fine it won't show on the surface.
It's flamability is higher because it's so fine but the resin is more flamable so the point is moot. Wood actually is far less flamable than synthetic ones. The navy went to all polyster uniforms until they went up in flames regretfully with sailors in them so they switched back to cotton blends I believe.
Ann, really ejoyed the article. Whenever we can repurpose natural and renewable resources as replacements for energy intensive manufactured goods it moves us in the right direction. Thanks.
Rob, I also figure that paper is a lot cheaper than glass, so these have got to be cheaper as fibers, plus they start out as fibers, which glass does not.
Lou, I understand your POV on US materials sources. Actually Weyerhaeuser owns forests in various parts of the world and expects to source cellulose from them as needed. Forests that can be harvested for wood products in northern temperate zones (there aren't many in southern ones) are no longer as common as you might think, including in the US.
Rob, we didn't get info on the fiber/glass cost differential, but considering that Weyerhauser's main business is wood pulp and wood products, I'd guess it's probably cheaper than glass.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
The 3D printing revolution seems to have a knack for quickly moving technology ahead by way of collaborative effort and even a little friendly competition -- all of course in the name of scientific advancement.
Advantech has launched a new series of motion-control I/O modules to meet the increased demands that come with more distributed industrial systems that require control of a growing number of axes and devices.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
4 
