HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
News
Electronics & Test

LEDs Need Circuit Protection, Too

NO RATINGS
1 saves
View Comments: Newest First|Oldest First|Threaded View
mrdon
User Rank
Gold
Re: Don't forget Thermal Design
mrdon   9/4/2012 2:50:33 PM
NO RATINGS
Hi LED MAC,

Very good points! Your absolutely correct regarding thermal manaagement concerns with LEDs and their driver circuits. Lumen maintenance failures caused by overdriving LEDs was the biggest challenge I faced when developing my lighting fixture prototypes at Hunter Fan. Although the LED continued emitting light, the opto-device was overstress by driving the component extremely hard with max current (Ifd). The naked eye couldn't see it put measuring its luminous flux showed the LED being degraded over time. In addition to protecting the overall product's system circuits from high voltage transients, thermal management must be high on the design priority list as well.

LED MAC
User Rank
Gold
Don't forget Thermal Design
LED MAC   9/4/2012 12:17:19 PM
NO RATINGS
LEDs are typically always the INDICATORS of failure, but not always the source of failure.  Improper circuit protection against abnormal conditions can just as easily kill a drive component as it would an LED, but the LED will almost always turn off due to any failure. (message to Quality guys...if it doesn't light up, it's not necessarily the LED's fault!)  

The failure that I see mostly is when the LED system design does not properly manage the heat generated within the LED  and/or drive electronics.  Good, worst case analysis should be done to ensure that the LED will always operate in a 'warm and fuzzy' region thus ensuring long and reliable life.    (note:  I don't have to design against lighting strikes!  That sounds tough!)

General rule of thumb; Lumen maintenance failures result from overdriving the LED (high current density), but catastrophic LED failure results from exceeding the Junction Temperature rating.   

mrdon
User Rank
Gold
Re: The forgotten issue
mrdon   8/26/2012 2:57:29 AM
NO RATINGS
notarboca, Thank you for the kind response. After seeing blue smoke let out of LED prototypes, there's a point where you start to think logical and document the exact function(s) required for the system/product under development.

notarboca
User Rank
Gold
Re: The forgotten issue
notarboca   8/26/2012 2:29:01 AM
NO RATINGS
@mrdon--I like your approach to this type of circuit design; it accentuates the positive from the requirements and minimalizes the negative effects of other design facets.  Well done, sir.

mrdon
User Rank
Gold
Re: The forgotten issue
mrdon   8/20/2012 11:30:43 AM
NO RATINGS
When I was designing LED lighting fixtures for a major ceiling fan supplier, I would immediately draw out a system block diagram including the power supply. Within this subcircuit block, I included all interconnects, transient suppression devices, and electromechanical devices. A detailed product specification will be written describing the functionality of the subcircuit blocks and their power and electrical requirements (Undervoltage, Overcurrent, etc) of the system block diagram. This engineering approach prevented significant damage to the prototype during testing because of the stringent transient electrical specifications spelled out in the design document.

naperlou
User Rank
Blogger
The forgotten issue
naperlou   8/20/2012 9:07:37 AM
NO RATINGS
This is indeed an issue with many electronic systems.  There are good CAE tools that would allow one to model these situations and to plan proper mitigation.  The software is expensive, though, and working with suppliers, like Littlefuse, can help avoid some of those costs.

Partner Zone
Latest Analysis
It's been two years since the Mac Mini's last appearance on iFixit's teardown table, but a newly revised version joins Apple's lineup this week.
More often than not, with the purchase of a sports car comes the sacrifice of any sort of utility. In other words, you can forget about a large trunk, extra seats for the kids, and more importantly driving in snowy (or inclement) weather. But what if there was a vehicle that offered the best of both worlds; great handling and practicality?
Kevin Gautier of Formlabs describes the making of a carbon fiber mold for an intake manifold, using a $3,300 3D printer, during Medical Design & Manufacturing Midwest.
Science fiction author Isaac Asimov may have the best rules for effective brainstorming and creativity. His never-before-published essay, "On Creativity," recently made it to the Web pages of MIT Technology Review.
Much has been made over the potentially dangerous flammability of lithium-ion batteries after major companies like Boeing, Sony, and Tesla have grappled with well-publicized battery fires. Researchers at Stanford University may have come up with a solution to this problem with a smart sensor for lithium-ion batteries that provides a warning if the battery is about to overheat or catch fire.
More:Blogs|News
Design News Webinar Series
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 20 - 24, How to Design & Build an Embedded Web Server: An Embedded TCP/IP Tutorial
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: 10/28-10/30 11:00 AM
Sponsored by Stratasys
Next Class: 10/28-10/30 2:00 PM
Sponsored by Gates Corporation
Next Class: 11/11-11/13 2:00 PM
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service