HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
News
Electronics & Test

LEDs Need Circuit Protection, Too

NO RATINGS
1 saves
View Comments: Newest First|Oldest First|Threaded View
mrdon
User Rank
Platinum
Re: Don't forget Thermal Design
mrdon   9/4/2012 2:50:33 PM
NO RATINGS
Hi LED MAC,

Very good points! Your absolutely correct regarding thermal manaagement concerns with LEDs and their driver circuits. Lumen maintenance failures caused by overdriving LEDs was the biggest challenge I faced when developing my lighting fixture prototypes at Hunter Fan. Although the LED continued emitting light, the opto-device was overstress by driving the component extremely hard with max current (Ifd). The naked eye couldn't see it put measuring its luminous flux showed the LED being degraded over time. In addition to protecting the overall product's system circuits from high voltage transients, thermal management must be high on the design priority list as well.

LED MAC
User Rank
Gold
Don't forget Thermal Design
LED MAC   9/4/2012 12:17:19 PM
NO RATINGS
LEDs are typically always the INDICATORS of failure, but not always the source of failure.  Improper circuit protection against abnormal conditions can just as easily kill a drive component as it would an LED, but the LED will almost always turn off due to any failure. (message to Quality guys...if it doesn't light up, it's not necessarily the LED's fault!)  

The failure that I see mostly is when the LED system design does not properly manage the heat generated within the LED  and/or drive electronics.  Good, worst case analysis should be done to ensure that the LED will always operate in a 'warm and fuzzy' region thus ensuring long and reliable life.    (note:  I don't have to design against lighting strikes!  That sounds tough!)

General rule of thumb; Lumen maintenance failures result from overdriving the LED (high current density), but catastrophic LED failure results from exceeding the Junction Temperature rating.   

mrdon
User Rank
Platinum
Re: The forgotten issue
mrdon   8/26/2012 2:57:29 AM
NO RATINGS
notarboca, Thank you for the kind response. After seeing blue smoke let out of LED prototypes, there's a point where you start to think logical and document the exact function(s) required for the system/product under development.

notarboca
User Rank
Gold
Re: The forgotten issue
notarboca   8/26/2012 2:29:01 AM
NO RATINGS
@mrdon--I like your approach to this type of circuit design; it accentuates the positive from the requirements and minimalizes the negative effects of other design facets.  Well done, sir.

mrdon
User Rank
Platinum
Re: The forgotten issue
mrdon   8/20/2012 11:30:43 AM
NO RATINGS
When I was designing LED lighting fixtures for a major ceiling fan supplier, I would immediately draw out a system block diagram including the power supply. Within this subcircuit block, I included all interconnects, transient suppression devices, and electromechanical devices. A detailed product specification will be written describing the functionality of the subcircuit blocks and their power and electrical requirements (Undervoltage, Overcurrent, etc) of the system block diagram. This engineering approach prevented significant damage to the prototype during testing because of the stringent transient electrical specifications spelled out in the design document.

naperlou
User Rank
Blogger
The forgotten issue
naperlou   8/20/2012 9:07:37 AM
NO RATINGS
This is indeed an issue with many electronic systems.  There are good CAE tools that would allow one to model these situations and to plan proper mitigation.  The software is expensive, though, and working with suppliers, like Littlefuse, can help avoid some of those costs.

Partner Zone
Latest Analysis
(Video) NASA's Modular Robotic Vehicle (MRV) is an EV inspired by manned rovers used for space exploration.
Comedian John Oliver recently did a segment on patent trolls, offering a hiliarious take on a serious issue plaguing US industries.
United Launch Alliance will fly 3D-printed flight hardeware parts on its rockets starting next year with the Atlas V. The company's Vulcan next-gen launch vehicle will have more than 100 production parts made with 3D printing. The main driver? Parts consolidation and 57% lower production costs.
The new small-form-factor EZ-BLE PRoC (Programmable Radio on Chip) module is a derivative of the existing PRoC BLE Programmable Radio-on-Chip solution. The EZ-BLE PRoC module integrates the programmability and ARM Cortex-M0 core of the PRoC BLE, two crystals, an onboard chip antenna, a metal shield, and passive components.
The engineers and inventors of the post WWII period turned their attention to advancements in electronics, communication, and entertainment. Breakthrough inventions range from LEGOs and computer gaming to the integrated circuit and Ethernet -- a range of advancements that have little in common except they changed our lives.
More:Blogs|News
Design News Webinar Series
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
5/7/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
May 4 - 8, Designing Low Power Systems using Battery and Energy Harvesting Energy Sources
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service