HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Feature
Materials & Assembly

Converting Machined Parts to Die Castings

NO RATINGS
Page 1 / 3 Next >
View Comments: Newest First|Oldest First|Threaded View
Greg M. Jung
User Rank
Platinum
Die Casting
Greg M. Jung   9/15/2012 3:36:50 PM
NO RATINGS
I agree that converting machined parts to die casting usually makes sense.  Because die casting tools can be expensive, it is important to first do a pay-back analysis and see if the volumes justify this change over.

In many cases we use both processes during the life of the product.  When the initial design is likely to change and we need to enter the market quickly, we may start with a machined part.  Then, as the design becomes stable and production volumes increase, we plan for a smooth cut-over to die cast tooling.

 

Dave Palmer
User Rank
Platinum
Comparing processes
Dave Palmer   8/6/2012 12:31:33 PM
NO RATINGS
In most cases, casting a part versus machining it from bar stock is a no-brainer.  In my career, I've only come across one part that made more sense as a screw-machined part than as a die casting.  In that case, the geometry of the part made it extremely easy to screw machine.  Also, screw machining allowed the part to be made out of a much stronger wrought alloy.  It wound up being an 80% cost savings (from $4 to about 80¢), along with a more than 50% increase in strength.

But this is far from the norm, and as this article shows, casting is almost always much cheaper.  A more interesting comparison would be between die casting and powder metallurgy.  It would also be worthwhile to compare different casting processes (die casting, semi-solid processing, permanent mold, investment casting, lost foam, etc.).  In addition to cost, these processes also vary in terms of the mechanical properties and dimensional accuracy that can be achieved.

Partner Zone
Latest Analysis
A Silicon Valley company has made the biggest splash yet in the high-performance end of the electric car market, announcing an EV that zips from 0 to 60 mph in 3.4 seconds and costs $529,000.
The biggest robot swarm to date is made of 1,000 Kilobots, which can follow simple rules to autonomously assemble into predetermined shapes. Hardware and software are open-source.
The Smart Emergency Response System capitalizes on the latest advancements in cyber-physical systems to connect autonomous aircraft and ground vehicles, rescue dogs, robots, and a high-performance computing mission control center into a realistic vision.
Tolomatic ERD actuator provides high-tolerance, high-force capabilities at a low cost to innovative medical therapy machine.
The diesel engine, long popular on European roads, is now piquing the interest of American automakers.
More:Blogs|News
Design News Webinar Series
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Sep 8 - 12, Get Ready for the New Internet: IPv6
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: September 30 - October 2
Sponsored by Altera
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service