HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Feature
Materials & Assembly

Converting Machined Parts to Die Castings

NO RATINGS
Page 1 / 3 Next >
View Comments: Newest First|Oldest First|Threaded View
Greg M. Jung
User Rank
Platinum
Die Casting
Greg M. Jung   9/15/2012 3:36:50 PM
NO RATINGS
I agree that converting machined parts to die casting usually makes sense.  Because die casting tools can be expensive, it is important to first do a pay-back analysis and see if the volumes justify this change over.

In many cases we use both processes during the life of the product.  When the initial design is likely to change and we need to enter the market quickly, we may start with a machined part.  Then, as the design becomes stable and production volumes increase, we plan for a smooth cut-over to die cast tooling.

 

Dave Palmer
User Rank
Platinum
Comparing processes
Dave Palmer   8/6/2012 12:31:33 PM
NO RATINGS
In most cases, casting a part versus machining it from bar stock is a no-brainer.  In my career, I've only come across one part that made more sense as a screw-machined part than as a die casting.  In that case, the geometry of the part made it extremely easy to screw machine.  Also, screw machining allowed the part to be made out of a much stronger wrought alloy.  It wound up being an 80% cost savings (from $4 to about 80¢), along with a more than 50% increase in strength.

But this is far from the norm, and as this article shows, casting is almost always much cheaper.  A more interesting comparison would be between die casting and powder metallurgy.  It would also be worthwhile to compare different casting processes (die casting, semi-solid processing, permanent mold, investment casting, lost foam, etc.).  In addition to cost, these processes also vary in terms of the mechanical properties and dimensional accuracy that can be achieved.

Partner Zone
Latest Analysis
The engineers and inventors of the post WWII period turned their attention to advancements in electronics, communication, and entertainment. Breakthrough inventions range from LEGOs and computer gaming to the integrated circuit and Ethernet -- a range of advancements that have little in common except they changed our lives.
The age of touch could soon come to an end. From smartphones and smartwatches, to home devices, to in-car infotainment systems, touch is no longer the primary user interface. Technology market leaders are driving a migration from touch to voice as a user interface.
Soft starter technology has become a way to mitigate startup stressors by moderating a motor’s voltage supply during the machine start-up phase, slowly ramping it up and effectively adjusting the machine’s load behavior to protect mechanical components.
A new report from the National Institute of Standards and Technology (NIST) makes a start on developing control schemes, process measurements, and modeling and simulation methods for powder bed fusion additive manufacturing.
If you’re developing a product with lots of sensors and no access to the power grid, then you’ll want to take note of a Design News Continuing Education Center class, “Designing Low Power Systems Using Battery and Energy Harvesting Energy Sources."
More:Blogs|News
Design News Webinar Series
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
5/7/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
May 4 - 8, Designing Low Power Systems using Battery and Energy Harvesting Energy Sources
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service