Researchers from the US Navy and the private sector have teamed up to design a new mobile photovoltaic system for charging batteries and supplying supplemental electricity. The system is meant to help the Marine Corp reduce fuel consumption.
Photovoltaic systems generate power by converting solar radiation into direct current electricity. They are part of the host of efforts by the military to use renewable energy sources, including new energy systems that use solar and wind power, which we've discussed before.
The Naval Research Laboratory has developed a photovoltaic prototype for the Marine Corps. The system is fitted to a standard USMC-issue backpack and includes a 10.5-inch x 15.5-inch solar panel that can generate more than 11W under 1-sun air mass of 1.5 illumination. (Source: Naval Research Lab)
Scientists at the US Naval Research Laboratory (NRL) Electronics Science and Technology Division are collaborating with MicroLinnk Devices, Design Intelligence Inc., and the USMC Expeditionary Energy Office to develop a solar power prototype that can recharge standard-issue lithium-ion batteries in the field.
The Defense Department says the system contains an array of single-junction solar cells with a power conditioning circuit, which maximizes array power production and can charge a military-issue, high-capacity, rechargeable lithium-ion battery (BB-2590). The system is designed to fit into a standard-issue backpack and includes a 10.5-inch x 15.5-inch solar panel that can generate 11W under 1-sun air mass of 1.5 illumination. The arrays take advantage of new technology that allows for a light-to-electricity conversion efficiency rate as high as 30 percent. The goal is not only to reduce energy consumption by 50 percent per Marine by using alternative sources of power, but also to lower the weight of batteries they carry by 200 pounds.
"One of the most significant challenges currently facing the Marine Corps is the need to supply sufficient electricity to individual Marines in forward operating bases," Robert Walters, head of the NRL Solid State Devices Branch, said in a press release. "Mobile photovoltaics are a technology that can address these needs by leveraging emerging, flexible, high-efficiency photovoltaic technology."
As we've reported before, the NRL is exploring other innovative uses for voltaics, including the development of solar cells that can operate electronic sensors under water at depths of up to 9m (about 30 feet). The cells are based on gallium indium phosphide, a material that performs better in low-light conditions than materials used in above-ground solar panels.
Sounds like this is going to help solve the energy problem for the solider on the go. Since soldiers are carrying increasing amounts of communication electronics, the batteries have become a burden. This could be the solution.
Great development. In addition to using electricity to operate electronic devices, I could see a soldier also using this to generate electrcity for a portable water purifier, which could further extend a soldier's range and duration.
Nothing new here and available for campers, etc at well stocked outdoor sports stores or online.
200lbs of batteries? Right!! That is far worse than the 30lb claim in another recent article here. Just not true for a standard soldier outfiting.
Nor would this unit replace that much battery. You can get 1kwhr in just 22lbs or less with lithium. even less if they didn't have to be rechargable. This unit would take 20 days to make that much power.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
6 
