The Defense Advanced Research Project Agency (DARPA) is testing a gauge that can determine the effects of explosions on soldiers in the field, even if their apparent injuries do not tell the full story.
The Blast Gauge -- a metal attachment that can be mounted on a helmet, other individual gear, or a military vehicle -- can measure the amount of exposure someone in the vicinity of a blast has had, according to the agency.
DARPA's Blast Gauge can be worn on the back of a soldier's helmet to determine the physical effects of a bomb or shrapnel blast during combat. The device includes a microprocessor and sensors that record and store blast event data to be examined later by medical personnel and researchers. (Source: DARPA)
Sensors in the device record the effects of a blast. A microprocessor at the core of the device controls the sensors and stores the information. Custom software inside the gauge senses and stores events relevant to blast exposure. A status light on the device alerts medical personnel to possible damage.
After a blast, field medics can check the device's status light, which comes up green, yellow, or red to indicate a soldier's relative risk of injury, Jeff Rogers, a DARPA program manager, said in a press release. "This is an entirely new capability and has already helped medics and doctors in treating injured warfighters."
The gauge also includes a micro-USB port that can make recorded data available to medical professionals treating the soldier or to researchers working on better responses to traumatic brain injury, according to DARPA. The device itself is a response to the prevalence of brain injuries in soldiers fighting in Iraq and Afghanistan.
After completing the first phase of a pilot test with about 900 soldiers in an active combat role, the Blast Gauge is now being used by more than 6,400 soldiers in various military units. The DoD said it expects to double that number in phase two of the pilot over the next month.
The Rochester Institute of Technology initially contracted with DARPA to develop the gauge. The development project took 11 months and cost about $1 million. BlackBox Biometrics is manufacturing the gauges.
Wearable technology that can help monitor soldier health in the field is a growing area of interest for the military. As we've reported, the DoD also is looking for a company to design and develop a uniform that includes sensors woven into the fabric that can measure the wearer's health, locate a wound, or detect exposure to biological or chemical weapons.
Quite a few years back my employer designed and built a system for evaluating the effects of a mine blasting an armored vehicle into the air. It seems that the landing was the problem, because a blast that will send a big truck 15 feet into the air will also blow off the wheels, so that it lands without benefit of the suspension. I have no idea what ultimate decisions were made with the data gained from that testing, but it was interesting to know that the problem was not in the blast but in the landing. I certainly did get to work on some interesting projects.
Yes, this is a great device, Chuck. It would be interesting to know what prompted the development of the device. Was it military medical professionals trying to gain a better understanding of what happens to the soldiers in the field? Probably so. If so, it's good to see the needs of military medical staff getting development response.
However they are only going to get the best a broken budget can give them. And the issue is not lack of money. It's the amount of money wasted. The million dollar hammers and wrenches that are ruining our troop's safety.
As much as I was going to poke fun at this device, I've changed my mind. I hope this helps with TBI treatment. The soldiers of this country deserve the best we can give them.
@JimT, I'm kind of on the fence too. Also, a light/LED may not be a great idea in a warzone especially at night. It may help the friends but foes see too. I know there are special LEDs and such for such applications and hopefully they have them written into their hardware design requirements.
Jim, I'm thinking that the value lies in telling the medical team what they might be dealing with, especially if aid is not immediately available. Did he get a minor conucussion and was only out for a few minutes? Are his injuries mostly from an explosion or was he overcome by something in the air? I agree with the other poster that weight might be an issue. Hopefully, something like this can be minimized so it can be as available as the radiation badges.
I agree that additional weight and restrictive equipment would be a huge negative, but as sensors go I think it is a good fit. Consider working with hazardous material without wearing a dosimeter. The function of this sensor appears to fit well with sensor canon -- extending the ability of our human senses to measure something that we are unable to transduce on our own. After treating the systems we can sense (airway, breathing, circulation) this Blast Gauge can be useful in treating head injuries and other hidden trauma; things Greg points out requiring immediate attention.
From the article, I'm inferring that the sensor outputs a red, yellow or green condition to assist the field medic in making a quick determination if head concussion and/or trauma is present. Then, the value of this sensor would be to help the medic make sure he/she doesn't miss a non-obvious head injury (when seconds count and life hangs in a delicate balance). This quick diagnosis seems like one of the benefits this sensor is intended to bring.
Hmmmm – not sure I endorse this, as I question what value it provides.It seems to be a shock sensor, very likely using a MEMS accelerometer and a small pill battery, to measure and log forces and impacts.While it will pass the SWAP (size, weight and power) criteria that footsoldiers demand against carrying extra gear, I'm not convinced it has real value added.Will a blinking light assist a medic in triage (evaluating worst first) ??There's no substitute for a real medic evaluating real bleeding injuries.I see this device as secondary reference to validate trauma evaluation, at best.Am I wrong-?
What a great device. Throughout many of our wars, soldiers have returned from battle with undiagnosed and misunderstood head injuries, many of which were caused by blasts nearby. It's great to see we're making an effort to understand those injuries more deeply. Hopefully, that understanding will translate to better treatments.
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
In a world that's going green, industrial operations have a problem: Their processes involve materials that are potentially toxic, flammable, corrosive, or reactive. If improperly managed, this can precipitate dangerous health and environmental consequences.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
