There has been an explosion of new camera interface standards for machine vision. In 2011, the industry got three. Two of them, finalized in March, apply only to machine vision and are found nowhere else: Camera Link HS and CoaXPress. The third, USB3 Vision, was announced for the first time in October by the Automated Imaging Association (AIA).
Unlike interface standards based on bus protocols designed specifically for vision, manufacturing engineers and quality control engineers also build vision systems based on general-purpose protocols such as USB 3.0, known as "SuperSpeed" USB. For only the second time -- GigE Vision was the first -- the industry is taking this one step further and codifying a vision-specific standard based on a bus already widely available in off-the-shelf hardware. The AIA expects to release the final version toward the end of 2012.
"All of these standards have different advantages and serve different needs," says Eric Gross, chairman of the AIA's USB3 Vision Committee, and senior software engineer for National Instruments' vision group. "In the case of USB3 Vision, that need is high speed, up to 3.2Gbit/s per cable, which is faster than all of the current standards except Camera Link HS and CoaXPress. Unlike them, a USB3 Vision camera can plug into any USB 3.0 port. These are about to become available on most PCs." Power and data can be run over the same cable up to five meters without amplification, compared to 45 meters for CoaXPress and 100 meters for GigE Vision.
USB has been the most successful interface in the history of the PC, in terms of volume. Ports are available on nearly all PCs, and increasingly on embedded hardware as well, says Gross. Many PCs also have Ethernet ports, but that interface is not as ubiquitous as it had been.
Many in machine vision adopted USB 2.0. But without a camera interface standard, anyone building a vision system had to use an SDK provided by the camera vendor. "This limits your application to the OS and devices that the camera vendor supports, which can be a problem if you're using cameras from multiple vendors. If you want to run the camera on an RTOS, you're out of luck unless the camera maker happens to have drivers for the specific RTOS you're using."
Seems like the dizzying array of standards would present huge challenges to engineers building machine vision applications and systems in terms of dealing with compatibility issues and a host of extra configuration work. Is this mix of standards holding back adoption of machine vision tools or is this something where there is a pretty standard workaround?
Beth, it's going to make me pause long and hard while trying to decide which protocol to use. This is a sore point for me; anyone who wants to adopt these early stands the chance of seeing that company's favorite protocol falling into disfavor.
Good point, Tim. It's ironic that on the one hand, the automation industry is attempting to get away from proprietary fieldbus protocols, which is leading to widespread adoption of Ethernet and new standards (e.g., for safety) being grafted on top of it. Yet here in the machine vision sector, which see forking and a battle among standards. The technical version of "can't we all just get along." More correctly, this is a typical market battle driven by advancing technology. USB3 is looking strong right now.
TJ and Alex, machine vision standards tend to be fairly long lived, at least in semiconductor "time", including the original Camera Link, now 11 years old. To date, none have fallen by the wayside. Also, none are single-sourced. It's true that some new standards have been promoted by a single company, but that's a normal process within any standards organization. And this seems to be happening less often. Several recent standards, not confined to machine vision, have been promoted by industry groups, as happened with WiFi, DisplayPort, and now USB3 Vision.
Another thing to keep in mind is that, in machine vision standards govern the camera interface, and very little else. Where things can become confusing is on the customer end, not so much on either the vendor or system integrator end. The confusion has to do with sorting out what's now a lot more choices than there used to be, and deciding what's best for your particular app.
Beth, I'm all for standards... as long as they make my job easier. The great thing about standards is that in an ever-evolving technology environment they are of most benefit to the early-adopters. Standardizing on VHS, ZIP-disks, or RS-232 were all fantastic choices at the time -- and then we (predictably) evolved. Spending lots of time fretting about which standard will be around in 10 - 15 years really isn't a relevant question. In 1998 I was tasked with building a system that integrated six (6) scientific-grade 1-Megapixel CCD cameras. The frame grabber boards could only support two (2) cameras each, so the solution was three (3) PCs with one running as a master and the other two running as slaves. The fastest interface at the time was Ethernet so after lots of low-level TCP code the system acted as a single unit. I would have killed for USB3. =]
I think there's some misunderstanding about machine vision standards, and the article's title may be a bit misleading. While some companies decide to adopt only one on the factory floor, for instance GigE because of its networking capabilities
the fact is that cameras compliant with more than one standard can often be mixed and matched in the same system or network (along with their frame grabbers if they have one). So there aren't really any major incompatibility issues.
Also, these standards are not created equal. They run at different speeds, use different types of cabling, etc. Only some of them are "proprietary," such as Camera Link and Camera Link HS, in the sense that their protocols are not used outside machine vision. The main big deal about GigE Vision and USB3 Vision is the fact that they are based on open, non-vision standards. Each vision standard is a specification, some very long and detailed, some pretty short, and each one governs the camera interface, either to a PC or to a frame grabber, or some other network device. Whether the spec is long and complicated or short and sweet depends on how much needs to be specified about things like data transfer conventions. In the case of USB3, these already exist, and so do the connectors, so very little is needed there.
What is wrong with CoaXpress? That is a good standard! USB3 is an unneeded standard thhat is destined to deliver inferior results due to inferior hardware. Besides that, the only ones destined to benefit from USB3 are those selling the hardware. The connector format is neither robust nor particularly reliable, and not suited for any application where a field repair may ever be needed.
I realize that promoting a standard that someone has a financial stake in is logical, but the real purpose of USB3 is to obsolete previous versions and make money for the sellers. It is not really in a position to fill anyother real need.
So let us instead consider the other standards that are able to fill the requirements and fill the need for robustness and reliability.
William, the one thing I can think of to justify a USB3.0 standard for vision is the availability of the interface as a standard feature of many computers. There is still a need for the others becuase of the limited cable distance that USB supports.
@naperlou -- I wasn't favoring USB3 over any of the competing interfaces, I was just cheer-leading for ALL interfaces. My primary function while in industry was that of integration. Our team would specify a dozen or so different components from a dozen or so different OEMs and it was my function to cobble them together and integrate them into a single system through the creation of custom software. At least for our situation, there was no such thing as going to the catalog, receiving a shrink-wrapped component, having a field service engineer install it and then have it running by the afternoon. It was spend a day to figure out what interface to use, receive those boards and drivers, spend a week or two to write the low-level communication drivers to get it communicating and then moving on to integrating it into our single platform -- all while doing the same for the other dozen or so OEM devices in parallel. When new interfaces come out, such as USB3, the standard has performed much of the low-level driver stuff. Since we had to work with ones and zeros anyway, I'm thankful for any help in the process regardless of how in/complete the standard or universal its current adoption. -Bill =]
I'd like to clarify another point: no camera or frame grabber vendor has a financial stake in only one machine vision standard. That would be business suicide on their part, because volumes are so small here compared to electronics, for example. What's happened, though, is that suddenly, instead of only offering maybe two choices, they must now consider offering two or three times that number, depending on where they are positioned in the market. Again, because volumes are low, this can be quite a strain, especially on the smaller vendors. So adding products based on a new standard is not a decision taken lightly.
I did not think that USB3 was common on industrial grade computers, since they are not the first to follow fads such as USB3. In addition to the limited cable length there is the lack of a repairable or field serviceable connector. That alone would be plenty to disqualify it from my consideration. A pair of fatal flaws is a fairly good reason to look at other interconnect standards.
William, my understanding is that USB3 is about to become a lot more common on laptops of all kinds. According to In-Stat, USB of all speeds is the most successful interface ever in terms of the number of electronic units shipped with it. The transition to USB 3 has been slower than the transitions to its previous revs:
Apparently, what's been holding it back has been less immediate need for its high speeds and the fact that it wasn't yet integrated in Intel's core logic chipsets. But that's apparently about to change:
Ann, the challenge of USB3 is exactly it's speed, and the resultant increased demand for a much more tightly controlled connection and transmission every bit of the way. The cables that were fine for USB 1 and USB2 just won't work for USB3. To top it off, nobody needs that speed except for the marketing departments that are hoping that we will all trash our present computers and buy new ones that include this "latest thing". The consumer electronics industry's goal has been to make each development obsolete in less than a year in order to create a market for the "next big thing". It has been this way for quite a few years, acknowledged in many of the trade publications.
William, thanks for the description of how totally not plug-and-play machine vision system design is. That's pretty much what I've heard several times--from vendors, about their customers. One of the biggest complaints I've heard over and over is the need to do exactly what you describe--write low-level driver software to get cameras and other components from multiple vendors to talk to each other. Nicely. And quickly. And without too many translation problems.
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
In a world that's going green, industrial operations have a problem: Their processes involve materials that are potentially toxic, flammable, corrosive, or reactive. If improperly managed, this can precipitate dangerous health and environmental consequences.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
