I think you're absolutely right, NYeng. This would not be an easy hurdle. I would guess that you're right about it being cost prohibitive. That's a shame, because this is a technically sound project.
I applaud this project from a technical and ingenuity standpoint.
However, I tend to agree with the pessimism on the regulatory stuff. Here in NY, the environmental hurdles as well as the federal & state energy commisions/authorities and utilities would make it nearly impossible. The thousands you would have to spend on attorneys, permits, fees, and political contributions to make it happen legally could buy you electric power from the utility for a hundred years or better. I think in this state the only thing attempting such a project would get you is legal trouble and the related fines and attorney fees.
The idea may or may not be impractical, but the comments are entusiastic. Those who comment on the Design News site are passionate about their views. I think that's very clear in this thread as well as the other comment threads.
Design News asked for people to moderate and presumably add comments to their web site. You had to make a certain number of posts to remain in the system and to receive a stipend or whatever it was called. I get the feeling that this thread is more about maintaining a posting record than making real comments about an idea that is impractical in almost every state.
You are absolutely correct. There's little more than .001 hp available from water @ 2 GPM dropping 2 feet. If this was able to produce 20 Kw we'd have ourselves a nice perpetual motion machine! I think that the heading of the article is misleading. The article itself is worthy.
This is a very good work! I wonder if this is affordable for developing countries like Mexico or Latin America where there is good potential for micro hydroelectric generation, how expensive is the system and where can I purchase one? Thanks
I have yet to connect our Micro Hydro to the grid. Except for a few hours of testing, when I discovered what 'absolute value' metering meant, we have been running autonomously since commissioning 2006. I used pumps as turbines and 3 phase motors as single phase generators to cut costs. I don't think I gave up any efficiency at all since I'm getting a bit more than my initial calculations indicated. NY just passed the net-metering law for under 25kW hydro, so we'll be hooking up soon.
Syncing induction generators of a few tens of KW to each other or the power-line is not a problem as long as they are within a few RPM or Hz of each other.
You're numbers look spot on. At that scale, standard induction motors might achieve 70%-80% efficiency, and the turbine/penstock losses are in that range as well.
Thank you, renuengineer for that explanation of how induction generation works; I couldn't have done it better!
Re: FERC, they don't involve themselves with individual installations this small. In South Carolina, our department of Health and Environmental Control does regulate dams & reservoirs, but our lake had already been in existence for over 100 years. The utility company was satisfied with some cursory drawings and assurance that we were entirely induction-based. The only official inspection was that of the county building department.
A new battery design, which replaces lithium with abundant and low-cost elemental sulfur, is still in its nascent stages but shows real promise for giving batteries more energy potential.
PTC will offer a virtual desktop environment for its Creo product design applications, potentially freeing engineers to run them from remote desktops on a variety of operating systems and mobile devices.
The push to achieving more intelligent, integrated manufacturing is putting a strong focus on networking and connectivity as key enabling technologies.
Now that solar and wind harvesting technologies are a thriving market, researchers are seeking other environmentally related energy sources for which they can create harvesting devices.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
