GM Says Volt Is Still On Schedule
DETROIT – General Motors (GM) engineers said Monday that they are still on track to produce the Chevy Volt plug-in hybrid by 2010, but that unforeseen problems with the battery or powertrain could push the introduction back to a later date.
“Normally, we pre-determine the design of the vehicle powertrain,” noted Frank Weber, global vehicle line executive and chief engineer of e-Flex Systems for GM. “But in the case of the Volt, we’re taking a much riskier path, where we are doing parallel development of the powertrain, battery, and vehicle itself.”
The highly-publicized Volt has drawn the interest of automotive community because it represents GM’s re-entry into the electric vehicle market. GM’s earlier entrant, known as the EV1, became a symbol of the electric vehicle movement’s failures when it was discontinued eight years ago. The EV1 was even the subject of a documentary movie, “Who Killed the Electric Car?”
Within the automotive engineering community, however, the Volt is considered vastly different because it uses an on-board internal combustion engine to supply power when its batteries run out of charge. Plans are for the car to have a 40-mile, battery-only driving range. When the batteries’ charge runs out, it will use the internal combustion engine to re-charge them, and gain as much as 600 more miles.
GM engineers said that this week that the giant automaker still harbors production intent for the vehicle. “It’s the project within GM that has the highest priority,” Weber said. “This is no scientific project and it’s no show car.”
The company has 500 engineers assigned to the project, Weber said.
Battery experts have questioned whether GM’s suppliers will be able to deal with some of the technical issues facing the project. Many believe that the battery packs, which will weigh more than 400 pounds, will cost too much to make the Volt profitable.
“We have always said this will be an expensive battery pack,” Weber said. “But once lithium-ion batteries are produced in higher volume, we expect the cost of those battery packs to go down significantly.”
Weber said EV batteries have improved tremendously in the past ten years. “In terms of energy and power, we have the same battery pack as the EV1, but it’s only one-third the size,” Weber said. “There is a very high confidence level that we can get it to the 40-mile range.”
Weber acknowledged, however, that any problems with the development of the battery pack could cause the car’s schedule to be pushed back. In that case, he said, the 2010 target “would be a stretch.”
Davidmac commented:
I will be due for a new vehicle in 2010; the Volt will be prefect for my daily commute of less than 40 miles. It will also alloy a small solar panel hooked to the grid to power it with perfect green appeal. I hope that the carbon expense to build it is not so excessive that it outweights the potential carbon savings. Anyone know if this information has been studied and posted anywhere?
Alan commented:
I havn't been this excited about a GM product in twenty years. I can't wait to be the first one on my block to own a Volt. That's saying a lot coming from a Ford man.
Mike Conaway commented:
Battery powered automobiles will at best be thinly sucessful as even a partial answer to our automotive transportation needs. Those who think otherwise simply do not understand energy storage, transmission, and conversion technolgies on a "dust to dust" basis and associated capital requirements. The greenest, most practical solution for the next 30 years is the turbo-charged diesel engine.
Ken Racz... commented:
Peoblems, problems, thats whe we have 500 Engineers working the project! When can I get one.
Brian P commented:
After GM perfects the Volt, how about a small Hybrid plug-in truck with Turbo Diesel Injection (TDI) which would allow me to put bio-diesel fuel thus generating zero CO2 if the electric charge comes from solar
DanF commented:
Me, too! By that I mean that I intend my next vehicle to be a Volt if possible. Ditto the "proud" remark as well. I do want to keep my eco-bucks in the country if I can. Just don't pull that lease-only crap again, please.
Steve commented:
Saving my pennies for a Volt. Thank you GM!
RAB commented:
This needs to happen for our country and for the world. Go GM! Make it happen and I will buy one!
Bill H commented:
I hope I can keep my current vehicle running long enough to replace it with a Volt! Once GM has the e-Flex system in production, they can drop just about ANY electricity producing device in place of the gasoline engine - turbodiesel, HCCI, or fuel cell - with the minimum possible redesign effort.
Brad commented:
My next car will be an evolution from the standard internal combustion engine. So, go GM as you're in the front seat for my next car!
John A commented:
This will set GM apart as the top technological innovator! This car just makes good sense and paves the way for electric transportation.
John commented:
The next new car I purchase will be a Volt, so keep at it! Consumers will reward GM for this.
Randy commented:
Give it hell GM!! Be the first to market this type of vehicle and you'll make me even prouder to be an American.
Sponsored Content
Design News Partner Zones
Light Matters: The Unsung Heroes of
Modern Health Care
First, let's define "no-compromise." In an ideal configuration, this lamp would use a high-brightness LED (HBLED) that is built into a small, integrated package and is able to produce a large quantity of focused light, operate with a high level of reliability and generate no audible noise. Is this difficult? Yes, but it is possible.
Read More
Design Engineers' Portal for Sensing and Machine Safety
Whatever industry you're in, or whatever product you manufacture, the right sensors to automate your plant, and to improve your overall efficiency, quality and safety are a must. You'll find Banner Engineering to be an amazing resource of products, training and people with expertise.
Test & Measurement World Machine Vision & Inspection Report
Topics include machine-vision software, Power over Camera Link, thermal imaging and frame grabbers. Read More















