This article brings back memories of ESD testing for me. At one place I worked we had a fairly sophisticated ESD tester and you could program in pin combinations and set voltage values and do just about anything you wanted. It came with different fixtures to fit different packages and you got your results stored to disk. Another place I worked at had a hand held ESD tester. You set your voltage and placed the tester head on the pin you wanted to zap (you literally put the device in a clamp and held the tester to each pin - you could program voltage and length of pulse if I recall correctly) and it was fun to use. You would then take the part for testing on your own test set. I always got a good laugh at the hand held model - it had a warning printed on the front "DO NOT USE AS A CATTLE PROD."
The author of the article has made some good points. We have come a LONG WAY in ESD protection but a designer should definately check specs to see if his application is in danger of getting zapped out of commission during normal use.
Chuck, the data sheet is important becuase it is the published detail on a product. This is what the vendor claims in public the device will do. So, as you point out, you need to read all of it. Depending on the device, they can be very long. There is also a lot of fine print because of the implications. If the customer has a problem and did not read the data sheet correctly, then it is their problem. If they read it correctly and had a problem, then it is the vendors problem.
I couldn't agree more. In my past experience as a design engineer, I've seen several of my peers select protection devices that ended up having double the capacitance from what they expected.
The value touted on the first page of the datasheet made for nice marketing, but that was only the capacitance of a single diode. When the protection device was connected in circuit there were 2 diodes per data line and therefore twice the capacitive load. Needless to say, they had to go back to the drawing board when their designs failed due to poor signal integrity!
You make a good point about the marketing aspects, Chad. In talking to you for this article, I realized I would have been one of the engineers who blindly trusted the numbers on the datasheet. Those numbers are, after all, data. But I suppose even data can be misleading, especially if we only present the data that puts us (or our product) in the best light.
A lot of engineers I know do not give the datasheet a full examination. Simple ESD protection is usually not on their minds at all. Just making it work seems to be the only focus. In fact, I have seen countless times where a static shock from handlers of the electronics destroy prototypes. Then everyone is head scratching over why it doesn't work.
Adding to this article, in addition to proper design application, there also needs to proper ESD handling procedures, training and equipment tests during manufacturing assembly. Improperly trained assemblers may not realize how easy it is to damage a sensitive electronic component. Also, regular ESD equipment checks need to be performed at each appropriate assembly station.
I remember one case where ESD damage was occurring even though proper foot straps and wrist straps were present. Upon further examination, it was found that the dissipative ESD floor wax was wearing thin and became ineffective (causing everyone to have a false sense of security when their foot and wrist straps were properly being used).
I think you make a good point, Greg - it's very important to enforce the procedures for ESD protection during manufacturing. Sometimes we would get some guy who would enter an area thinking that the rules didn't apply to him - and then people wondered why our RMAs showed ESD damage...
Admittedly, I was not aware of all the anti-ESD measures that need to be taken by manufacturers. But the dissipative floor wax is still a surpise to me.
Yes, the dissipative floor wax is a very expensive product and must be reapplied on a regular basis. However, its a great way to control static through ESD shoes, shoe straps or chains hanging from PCB carts.
Greg's points are the best action for dealing with static sensitive devices. But Its both smart product design, AND preventative measures during fabrications.
When PCBs are open & exposed (during manufacturing) ESD wrist straps, ESD jackets, boot straps, and grounded desk pads must be in place. Any manufacturing center dealing with open electronics & fabrication processes has all of these elements implemented on the production floor.
After finished goods are distributed to consumers, the product envelope must be sufficiently insulated to prevent that "carpet-static" and other ESD effects. That goes back to the effective design of the housing enclosures, in the first place.
A new book by Thomas Edison's great-grandniece takes on the notion that he was a lone-wolf inventor and replaces it with an image of a man who ascribed great value to the ideas of colleagues.
In response to rising interest in autonomous vehicles, the federal government has called upon states not to authorize operation of self-driving cars, except for the purpose of testing.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
23 
