HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Electronic News & Comment
The Secret to Eliminating ESD Damage? Read Your Datasheet
11/21/2012

A typical IEC 61000-4-2 ESD waveform is characterized by its sub-nanosecond rise time and its short (~100 ns) duration.   (Source: Littelfuse Inc.)
A typical IEC 61000-4-2 ESD waveform is characterized by its sub-nanosecond rise time and its short (~100 ns) duration.
(Source: Littelfuse Inc.)

Return to Article

View Comments: Oldest First|Newest First|Threaded View
Nancy Golden
User Rank
Platinum
Different Ways Manufacturers ESD Test
Nancy Golden   11/21/2012 9:35:58 AM
NO RATINGS
This article brings back memories of ESD testing for me. At one place I worked we had a fairly sophisticated ESD tester and you could program in pin combinations and set voltage values and do just about anything you wanted. It came with different fixtures to fit different packages and you got your results stored to disk. Another place I worked at had a hand held ESD tester. You set your voltage and placed the tester head on the pin you wanted to zap (you literally put the device in a clamp and held the tester to each pin - you could program voltage and length of pulse if I recall correctly) and it was fun to use. You would then take the part for testing on your own test set. I always got a good laugh at the hand held model - it had a warning printed on the front "DO NOT USE AS A CATTLE PROD."

The author of the article has made some good points. We have come a LONG WAY in ESD protection but a designer should definately check specs to see if his application is in danger of getting zapped out of commission during normal use.

naperlou
User Rank
Blogger
Data Sheets Important
naperlou   11/21/2012 11:00:59 AM
NO RATINGS
Chuck, the data sheet is important becuase it is the published detail on a product.  This is what the vendor claims in public the device will do.  So, as you point out, you need to read all of it.  Depending on the device, they can be very long.  There is also a lot of fine print because of the implications.  If the customer has a problem and did not read the data sheet correctly, then it is their problem.  If they read it correctly and had a problem, then it is the vendors problem. 

Greg M. Jung
User Rank
Platinum
Good ESD Manufacturing Practices
Greg M. Jung   11/25/2012 8:23:50 PM
NO RATINGS
Adding to this article, in addition to proper design application, there also needs to proper ESD handling procedures, training and equipment tests during manufacturing assembly.  Improperly trained assemblers may not realize how easy it is to damage a sensitive electronic component.  Also, regular ESD equipment checks need to be performed at each appropriate assembly station. 

I remember one case where ESD damage was occurring even though proper foot straps and wrist straps were present.  Upon further examination, it was found that the dissipative ESD floor wax was wearing thin and became ineffective (causing everyone to have a false sense of security when their foot and wrist straps were properly being used).

Nancy Golden
User Rank
Platinum
Re: Good ESD Manufacturing Practices
Nancy Golden   11/26/2012 12:26:40 PM
NO RATINGS
I think you make a good point, Greg - it's very important to enforce the procedures for ESD protection during manufacturing. Sometimes we would get some guy who would enter an area thinking that the rules didn't apply to him - and then people wondered why our RMAs showed ESD damage...

Charles Murray
User Rank
Blogger
Re: Good ESD Manufacturing Practices
Charles Murray   11/26/2012 6:37:58 PM
NO RATINGS
Admittedly, I was not aware of all the anti-ESD measures that need to be taken by manufacturers. But the dissipative floor wax is still a surpise to me.   

Greg M. Jung
User Rank
Platinum
Re: Good ESD Manufacturing Practices
Greg M. Jung   11/26/2012 9:05:59 PM
NO RATINGS
Yes, the dissipative floor wax is a very expensive product and must be reapplied on a regular basis.  However, its a great way to control static through ESD shoes, shoe straps or chains hanging from PCB carts.

JimT@Future-Product-Innovations
User Rank
Blogger
Re: Good ESD Manufacturing Practices
JimT@Future-Product-Innovations   11/27/2012 1:20:37 PM
NO RATINGS
Greg's points are the best action for dealing with static sensitive devices.  But Its both smart product design, AND preventative measures during fabrications.

When PCBs are open & exposed (during manufacturing) ESD wrist straps, ESD jackets, boot straps, and grounded desk pads must be in place.  Any manufacturing center dealing with open electronics & fabrication processes has all of these elements implemented on the production floor.

After finished goods are distributed to consumers, the product envelope must be sufficiently insulated to prevent that "carpet-static" and other ESD effects.  That goes back to the effective design of the housing enclosures, in the first place.

Chad Marak
User Rank
Iron
Re: Data Sheets Important
Chad Marak   11/28/2012 3:06:33 PM
NO RATINGS
I couldn't agree more.  In my past experience as a design engineer, I've seen several of my peers select protection devices that ended up having double the capacitance from what they expected. 

The value touted on the first page of the datasheet made for nice marketing, but that was only the capacitance of a single diode.  When the protection device was connected in circuit there were 2 diodes per data line and therefore twice the capacitive load.  Needless to say, they had to go back to the drawing board when their designs failed due to poor signal integrity!

 

Charles Murray
User Rank
Blogger
Re: Data Sheets Important
Charles Murray   11/28/2012 6:25:48 PM
NO RATINGS
You make a good point about the marketing aspects, Chad. In talking to you for this article, I realized I would have been one of the engineers who blindly trusted the numbers on the datasheet. Those numbers are, after all, data. But I suppose even data can be misleading, especially if we only present the data that puts us (or our product) in the best light.  

Cabe Atwell
User Rank
Blogger
Re: Data Sheets Important
Cabe Atwell   2/6/2013 5:12:53 PM
NO RATINGS
A lot of engineers I know do not give the datasheet a full examination. Simple ESD protection is usually not on their minds at all. Just making it work seems to be the only focus. In fact, I have seen countless times where a static shock from handlers of the electronics destroy prototypes. Then everyone is head scratching over why it doesn't work.

C

Partner Zone
More Blogs from Electronic News & Comment
If the design of Subaru’s XV Crosstrek Hybrid car is any indication, we may now be seeing the next new wrinkle in the evolution of automotive test simulation.
Despite recent news reports to the contrary, cold winter weather was probably no more than a minor contributor to the Boeing 787’s lithium-ion battery fires last year.
Using sensors and a specialized test stand, engineers have discovered that the root causes of head trauma may lie in a complex pattern of forces that today’s football helmets aren’t equipped to handle.
Lithium-ion batteries will soon back up the power grid on the Hawaiian island of Kauai, providing the stability to handle intermittent power fluctuations from renewable energy sources.
Self-driving vehicle technology could grow rapidly over the next two decades, with nearly 95 million “autonomous-capable” cars being sold annually around the world by 2035, a new study predicts.
Design News Webinar Series
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 18 - 22, Embedded Software Development With Python & the Raspberry Pi
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: September 30 - October 2
Sponsored by Altera
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service