At the Automation Fair, Rockwell engineers said that manufacturers and machine builders are increasingly migrating toward Ethernet. They described beverage and tire manufacturers, along with an major aluminum manufacturer and an auto company that have recently adopted EtherNet/IP. Today, approximately 60% of the automation equipment sold by Rockwell is Ethernet-based, they said.
"EtherNet/IP is the most popular protocol in the industrial sector right now," Kann told us.
Part of that popularity stems from an a partnership with networking giant Cisco Systems, Inc. Starting in 2006, the two companies worked together on the development of an Ethernet-based protocol, with Cisco doing the networking part of the development and Rockwell doing the controls.
At the Automation Fair, Rockwell rolled out the Stratix 5700 Managed Switch, created in partnership with Cisco. The small form factor Ethernet switch is targeted at machine builders -- a user community that has also started moving toward the Ethernet world. Rockwell also introduced an Ethernet adapter, Ethernet cables and an Ethernet/IP encoder.
Migration toward Ethernet also appears to be opening up opportunities for Cisco, which says that its industrial business is now growing at 50 percent annually. "It's been a change for us, in terms of understanding the applications and understanding what's needed," noted Chet Namboodri, global director of solutions and marketing for Cisco Industrial Intelligence. "But it's also becoming a significant business for Cisco."
To be sure, Rockwell and Cisco aren't the only ones pushing migration to Ethernet. There are now multiple strains of Ethernet on the factory floor, including Profinet, Ethernet Powerlink, EtherCAT, SERCOS III, and others. Moreover, many engineers still prefer the fieldbuses, largely because they know the technology and want to leave well-enough alone.
"There are still some corners of industry where the fieldbuses are hanging around," Kann said. "But that's slowly changing."
Engineers at the show said the biggest draw for major manufacturers is the ability to tie their Ethernet-based IT systems to the shop floor. Doing so gives them remote access to the factory that didn't always exist in the past.
"It's irreversible in our opinion," Kann said. "The future bodes well that it will continue."
Ethernet as a standard on the factory was really inevitable given the requirement to sync up production systems with front-office IT systems like ERP and even PLM. It is only with that kind of tight integration that companies can hope to garner the visibility and traceability necessary for boosting the efficiency of their production systems and moving to just-in-time manufacturing.
I had assumed that the migration to Ethernet was a done deal. I guess this article is saying that it is, but that not everyone has made the shift yet. I think we're also seeing something of a taxonomy/nomenclature problem, which is something that has plagued the whole discussion of fieldbuses for a long time. Namely, Ethernet isn't so much REPLACING field buses as it is BECOMING the new, de factor field bus standard (via protocols layered on top of it for safety etc.)
Ethernet has taken a really long time to move into the control world, because of the multiple silos created by different proprietary protocols and because of the big difference in functionality between control protocols and the serial, packet-based Ethernet networking protocols. The determinism issue was a real one. That's why it's taken protocols specially designed for real-time industrial control, such as EtherCAT and Ethernet Powerlink, to make that shift possible.
One of the fun side effects of IT and plant control running on the same Ethernet pipeline is the question of who's in charge? That battle has been raging for years. Some smart companies have created mixed groups with personnel from both IT and control. But that's not always the case.
They have two different views of the world. IT is concerned about security and control is concerned about uptime. In the past, control was an internal network without security issues. That's changed.
Even though Ethernet (the hardware) is becoming standard, the hiccup is the fact that each manufacturer maintains its own protocols. While you can buy an off-the-shelf industrial switch from anybody for your system, that's only half the battle. There is still no easy way (short of bridges or converters) to take Manufacturer A's product and put it into an existing system that used Manufacturer B. The issue gets blown out of proportion when dealing with non-automation people who can't quite grasp why interoperation is not so easy when "they are all ethernet, aren't they?"
You raise a really important point, Rob. And with control systems becoming a more fully blended mix of traditional automation and mainstream IT technology, it's logical that the person in charge has to straddle or have some sort of oversight of both domains. Perhaps there is an emerging new position?
Yes, it's a widespread conflict. IT says, you need these patches to ensure your security. Control says, you can't reboot these computers until we have planned downtime. The big change is that the control network is exposed to the outside world now that the plant's control network is tied in to ERP and supply chain networks.
This kind of integration is great. The finance folks know what's being consumed and what's being produced. Suppliers know what inventory has been depleted. Customers get to know when their M&Ms have shipped. But the plant is now exposed to all the contagious ills that run on the Internet.
Over 6 years of meetings between IT and Controls, there is more emphasis on security from the Controls side now that we have a greater understanding. The controls were determined that IT be "like the cable company" and provide the infrastructure only.
The largest gap now is the issue of urgency, Controls live in a world where "real-time" is milliseconds and IT's definition is hours.
Very interesting, Dave. Sounds like IT backed off once they were convinved that control got religion on the importance of security. Seems like an excellent solution. And yes, you identified another area of conflict between IT and control, the sense of time.
That's an excellent point about security, Rob. One of the good things about the pre-internet days was that, even if you could hack a machine based on one of those old proprietary standards, they weren't connected to the outside world. Now they are, and all that data is exposed.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
We recently posted an online slideshow called, “18 People You Didn’t Know Were Engineers.” Within hours of its publication, readers began to suggest names of other luminaries -- astronauts, politicians, athletes and actors -- who were educated or had worked as engineers.
In yet another sign that hydrogen is creeping into the consciousness of global automotive designers, sports car maker Aston Martin plans to run a hydrogen-fueled vehicle in a 24-hour Grand Touring race later this month.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
11 
