HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Electronic News & Comment
The Secret to Eliminating ESD Damage? Read Your Datasheet
11/21/2012

A typical IEC 61000-4-2 ESD waveform is characterized by its sub-nanosecond rise time and its short (~100 ns) duration.   (Source: Littelfuse Inc.)
A typical IEC 61000-4-2 ESD waveform is characterized by its sub-nanosecond rise time and its short (~100 ns) duration.
(Source: Littelfuse Inc.)

Return to Article

View Comments: Threaded|Newest First|Oldest First
Nancy Golden
User Rank
Platinum
Different Ways Manufacturers ESD Test
Nancy Golden   11/21/2012 9:35:58 AM
NO RATINGS
This article brings back memories of ESD testing for me. At one place I worked we had a fairly sophisticated ESD tester and you could program in pin combinations and set voltage values and do just about anything you wanted. It came with different fixtures to fit different packages and you got your results stored to disk. Another place I worked at had a hand held ESD tester. You set your voltage and placed the tester head on the pin you wanted to zap (you literally put the device in a clamp and held the tester to each pin - you could program voltage and length of pulse if I recall correctly) and it was fun to use. You would then take the part for testing on your own test set. I always got a good laugh at the hand held model - it had a warning printed on the front "DO NOT USE AS A CATTLE PROD."

The author of the article has made some good points. We have come a LONG WAY in ESD protection but a designer should definately check specs to see if his application is in danger of getting zapped out of commission during normal use.

naperlou
User Rank
Blogger
Data Sheets Important
naperlou   11/21/2012 11:00:59 AM
NO RATINGS
Chuck, the data sheet is important becuase it is the published detail on a product.  This is what the vendor claims in public the device will do.  So, as you point out, you need to read all of it.  Depending on the device, they can be very long.  There is also a lot of fine print because of the implications.  If the customer has a problem and did not read the data sheet correctly, then it is their problem.  If they read it correctly and had a problem, then it is the vendors problem. 

Chad Marak
User Rank
Iron
Re: Data Sheets Important
Chad Marak   11/28/2012 3:06:33 PM
NO RATINGS
I couldn't agree more.  In my past experience as a design engineer, I've seen several of my peers select protection devices that ended up having double the capacitance from what they expected. 

The value touted on the first page of the datasheet made for nice marketing, but that was only the capacitance of a single diode.  When the protection device was connected in circuit there were 2 diodes per data line and therefore twice the capacitive load.  Needless to say, they had to go back to the drawing board when their designs failed due to poor signal integrity!

 

Charles Murray
User Rank
Blogger
Re: Data Sheets Important
Charles Murray   11/28/2012 6:25:48 PM
NO RATINGS
You make a good point about the marketing aspects, Chad. In talking to you for this article, I realized I would have been one of the engineers who blindly trusted the numbers on the datasheet. Those numbers are, after all, data. But I suppose even data can be misleading, especially if we only present the data that puts us (or our product) in the best light.  

Cabe Atwell
User Rank
Blogger
Re: Data Sheets Important
Cabe Atwell   2/6/2013 5:12:53 PM
NO RATINGS
A lot of engineers I know do not give the datasheet a full examination. Simple ESD protection is usually not on their minds at all. Just making it work seems to be the only focus. In fact, I have seen countless times where a static shock from handlers of the electronics destroy prototypes. Then everyone is head scratching over why it doesn't work.

C

Greg M. Jung
User Rank
Platinum
Good ESD Manufacturing Practices
Greg M. Jung   11/25/2012 8:23:50 PM
NO RATINGS
Adding to this article, in addition to proper design application, there also needs to proper ESD handling procedures, training and equipment tests during manufacturing assembly.  Improperly trained assemblers may not realize how easy it is to damage a sensitive electronic component.  Also, regular ESD equipment checks need to be performed at each appropriate assembly station. 

I remember one case where ESD damage was occurring even though proper foot straps and wrist straps were present.  Upon further examination, it was found that the dissipative ESD floor wax was wearing thin and became ineffective (causing everyone to have a false sense of security when their foot and wrist straps were properly being used).

Nancy Golden
User Rank
Platinum
Re: Good ESD Manufacturing Practices
Nancy Golden   11/26/2012 12:26:40 PM
NO RATINGS
I think you make a good point, Greg - it's very important to enforce the procedures for ESD protection during manufacturing. Sometimes we would get some guy who would enter an area thinking that the rules didn't apply to him - and then people wondered why our RMAs showed ESD damage...

Charles Murray
User Rank
Blogger
Re: Good ESD Manufacturing Practices
Charles Murray   11/26/2012 6:37:58 PM
NO RATINGS
Admittedly, I was not aware of all the anti-ESD measures that need to be taken by manufacturers. But the dissipative floor wax is still a surpise to me.   

Greg M. Jung
User Rank
Platinum
Re: Good ESD Manufacturing Practices
Greg M. Jung   11/26/2012 9:05:59 PM
NO RATINGS
Yes, the dissipative floor wax is a very expensive product and must be reapplied on a regular basis.  However, its a great way to control static through ESD shoes, shoe straps or chains hanging from PCB carts.

JimT@Future-Product-Innovations
User Rank
Blogger
Re: Good ESD Manufacturing Practices
JimT@Future-Product-Innovations   11/27/2012 1:20:37 PM
NO RATINGS
Greg's points are the best action for dealing with static sensitive devices.  But Its both smart product design, AND preventative measures during fabrications.

When PCBs are open & exposed (during manufacturing) ESD wrist straps, ESD jackets, boot straps, and grounded desk pads must be in place.  Any manufacturing center dealing with open electronics & fabrication processes has all of these elements implemented on the production floor.

After finished goods are distributed to consumers, the product envelope must be sufficiently insulated to prevent that "carpet-static" and other ESD effects.  That goes back to the effective design of the housing enclosures, in the first place.

Partner Zone
More Blogs from Electronic News & Comment
The data breaches at Target, Home Depot, and elsewhere have inadvertently highlighted a separate and unexpected problem: bad user interface design.
Peter Riendeau of Melexis shows how a time-of-flight sensor can be used for gesture recognition in a vehicle.
David Bottomley of Delphi Electronics demonstrates Delphi Connect, which allows do-it-yourselfers to add connectivity and onboard diagnostics to their existing vehicles.
A tiny new tire pressure monitoring package will fit inside the tire, instead of on the stem, enabling vehicles to gather more information and help set the stage for self-driving cars.
Peter Riendeau of Melexis demonstrates how a LIN data bus can be used to change the color of ambient interior lighting in a car with just the swipe of a hand.
Design News Webinar Series
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Nov 3 - 7, Engineering Principles behind Advanced User Interface Technologies
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: 10/30 11:00 AM
Sponsored by Stratasys
Next Class: 10/30 2:00 PM
Sponsored by Gates Corporation
Next Class: 11/11-11/13 2:00 PM
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service