Inspection of composites used in aircraft such as the A350 XWB, shown here in Getafe, Spain, during
initial horizontal tailplane assembly, may be assisted by research into coatings
that will make damage visible at certain wavelengths.
Dave, You just articulated the point that I was trying to make so much better than I did. It does seem like a no-brainer, especially if the technology has been around for a while. I'm wondering what hurdles there were preventing this from being put to use in any significant form prior to now. Or maybe it's that there wasn't a formal market for something like this given that composite materials are just now becoming so dominant in aerospace design.
Thanks, William and Dave, for sharing your experience in this area. It surprises me that using composites as a repair material for aluminum didn't strike anyone as not a good idea, since their properties are so different. To my limited knowledge so far, repair materials for composites are supposed to pretty closely match the material they are replacing.
The whole subject of using coatings to monitor structural health does seem obvious, doesn't it? I notice that Stresscoat does not appear to address composites. The big deal about them is the fact that damage can be invisible, hence the attempts to make it visible under other wavelengths. And yes, you would think that research such as GKN's would have already occurred, and perhaps it has. Theirs was not easy to find, so it's possible there's other such research going on quietly.
Beth, I understand that designing these different coatings is equally simple, whether one coating detects one energy level or multiple energy levels. Creating the actual coating may be a different story, but that wasn't entirely clear. In any case, GKN said it plans to sell the coatings as an integral part of its composite aircraft structural components, not as a separate product line.
Coatings such as Stresscoat have been used in experimental stress analysis for decades. It seems like a no-brainer to use something like this for structural health monitoring. Of course, it's easy to say that something is a no-brainer after someone else has already come up with it. I'm just surprised that nobody came up with something like this sooner.
Thanks for the article Ann! It is great to see this technology being commercialized and incorporated into engineering materials. I was involved in the development of diagnostic coatings which, when excited and viewed under specific wavelengths, provided surface information of temperature, pressure, strain, and cracks. The coatings were applied to the surface of the completed unit for testing. I'm delighted to learn of continued development of both surface and internal coatings during component manufacturing.
One of our biggest surprises came from using composite repair material when applied to traditional metals (aircraft aluminium). Our coatings were used to inspect the performance of a "composite Band-Aid" that could be used to field dress a fatigue crack until the panel could be replaced. The difficulty was that the mechanical performance of the composite material was so superior to the original alloy that the repair site was often a greater point of additional fatigue cracking in the original metal because of the sharp differences between the materials. I imagine things will be better and far superior when all of the components are made out of advanced composites in the first place.
Very cool piece of development and one that would certainly benefit broader use of composites. The idea that a coating could deliver intelligent inspection capabilities is in some ways out there, but then again, in keeping with steady pace of technological advances. In many ways, the development strategy makes perfect sense. Do you have a sense of how difficult or how unique it is to develop a single coating with different signatures that can appear different depending on different energy levels of impact?
BMW has already incorporated more than 10,000 3D-printed parts in the Rolls-Royce Phantom and intends to expand the use of 3D printing in its cars even more in the future. Meanwhile, Daimler has started using additive manufacturing for producing spare parts in Mercedes-Benz Trucks.
SABIC's lightweighting polycarbonate glazing materials have appeared for the first time in a production car: the rear quarter window of Toyota's special edition 86 GRMN sports car, where they're saving 50% of its weight compared to conventional glass.
Design engineers play a big role in selecting both suppliers and materials for their designs. Our most recent Design News Materials Survey says they continue to be highly involved, in some ways even more than the last time we asked to peek inside their cubicles.
Daihatsu is one of the first carmakers to customize car exteriors using 3D printing's mass customization capabilities. Effect Skins -- small exterior bumper and fender panels in different colors and textures -- can be ordered for its Copen convertible.
Several new products in this group of new adhesives, coatings, and sealants are formulated to protect sensitive electronic components, or to seal components of commercial and military aircraft. Others are designed to operate in tough, messy, dirty oil & gas operations, or for rotary applications and motors.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies.
You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived.
So if you can't attend live, attend at your convenience.