HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Engineering Materials

Self-Healing Gel Could Replace Cartilage

NO RATINGS
View Comments: Oldest First|Newest First|Threaded View
<<  <  Page 3/4  >  >>
Ann R. Thryft
User Rank
Blogger
Re: HYDROGEL
Ann R. Thryft   10/8/2012 6:22:41 PM
NO RATINGS
bobj, glad you liked the article. I hope you were doing all that running on earth, not concrete. This technology is very much in its infancy, as are most of the discoveries I write on reported by universities, instead of commercial companies. That said, hydrogels as a class have a history as cartilage replacements already, so the timeline might be shorter than "normal," if there is such a thing. I guess growing up in Silicon Valley makes me appreciative of Heiseneberg. Anyway, I also have hip issues, although so far only in winter.

Charles Murray
User Rank
Blogger
Re: Replacement for cartilage is intriguing
Charles Murray   10/9/2012 7:33:15 PM
NO RATINGS
Thanks, mydesign. Do you know if the magnetic technique works for someone who has almost no cartilage left?

Greg M. Jung
User Rank
Platinum
Time to Market
Greg M. Jung   10/11/2012 9:16:55 PM
NO RATINGS
Given that Hydrogels are already being used for cartilage replacement, what would the best case scenario be for getting this new material approved for use?  Would clinical trials first be required?

Mydesign
User Rank
Platinum
Re: Replacement for cartilage is intriguing
Mydesign   10/12/2012 1:02:39 AM
NO RATINGS
1 saves
Charles, they are clamming that more than 90% of cartilages can regenerate through magnetic therapy within 6-9 months. Moreover, they had shown me some of the cases of their old patients. But when I check with other medical professionals, they said, it's a like a form of alternate medicine and so far it's not medically proven. Bit confusing!!

Mydesign
User Rank
Platinum
Re: Knee Cartilage
Mydesign   10/12/2012 1:11:28 AM
NO RATINGS
1 saves
Ann, as of now knee replacement surgery is the only proven and effective treatment for cartilage wear & tear. Ofcource there are some treatments in alternative medicines like Homeopathy, Ayurveda, Magnetic therapy etc. But such treatments are not widely accepted and even not medically proven. They will first do the treatment for pain management and for most of the patients that's enough to get relief.

Ann R. Thryft
User Rank
Blogger
Re: Knee Cartilage
Ann R. Thryft   10/12/2012 11:59:52 AM
NO RATINGS
Mydesign, I looked into various forms of magnetic "healing" back in the 1990s. Some alternative medicine methods actually work, sometimes or even a lot of the time. But so-called magnetic therapy is just a false claim. You're right, surgery is the only proven method of treating cartilage problems. Too bad it's so expensive.

notarboca
User Rank
Gold
Re: Knee Cartilage
notarboca   10/15/2012 5:35:59 AM
NO RATINGS
As a person with an ACL replacement (1988)  and subsequent wear damage to the meniscus and surrounding cartilage, I can only hope this material is approved for surgical applications within the next few years.

Mydesign
User Rank
Platinum
Re: Knee Cartilage
Mydesign   10/16/2012 12:20:57 AM
NO RATINGS
1 saves
"You're right, surgery is the only proven method of treating cartilage problems. Too bad it's so expensive."

Ann, in my country knee replace surgeries are cheaper when compare with the magnetic therapy for cartilage regeneration. A complete single knee replacement cost you less than $3000. At the same time for magnetic therapy they are charging $500-600 per sitting and it require minimum of 6-9 sittings.

Ann R. Thryft
User Rank
Blogger
Re: Knee Cartilage
Ann R. Thryft   10/16/2012 12:01:18 PM
NO RATINGS
Mydesign, I knew the cost of surgery is much lower in non-Western countries, but that's hugely less. And the cost for magnetic therapy looks a lot higher than here (at least the last time I checked several years ago).

Ann R. Thryft
User Rank
Blogger
Re: Knee Cartilage
Ann R. Thryft   10/18/2012 7:55:04 PM
NO RATINGS
notarboca, I'd like to see this commercialized ASAP so I can get a new knee that's got a chance of working right.

<<  <  Page 3/4  >  >>
Partner Zone
More Blogs from Engineering Materials
Although plastics make up only about 11% of all US municipal solid waste, many are actually more energy-dense than coal. Converting these non-recycled plastics into energy with existing technologies could reduce US coal consumption, as well as boost domestic energy reserves, says a new study.
This year's Dupont-sponsored WardsAuto survey of automotive designers and other engineers shows lightweighting dominates the discussion. But which materials will help them meet the 2025 CAFE standards are not entirely clear.
Artificially created metamaterials are already appearing in niche applications like electronics, communications, and defense, says a new report from Lux Research. How quickly they become mainstream depends on cost-effective manufacturing methods, which will include additive manufacturing.
SpaceX has 3D printed and successfully hot-fired a SuperDraco engine chamber made of Inconel, a high-performance superalloy, using direct metal laser sintering (DMLS). The company's first 3D-printed rocket engine part, a main oxidizer valve body for the Falcon 9 rocket, launched in January and is now qualified on all Falcon 9 flights.
A new thermoplastic composite for high-speed, high-volume injection molding has tensile strength that's close to, and sometimes better than, either lay-up composites or metals.
Design News Webinar Series
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Sep 8 - 12, Get Ready for the New Internet: IPv6
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: September 30 - October 2
Sponsored by Altera
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service