A major advance in repairing composite components bodes well for commercial aircraft that contain composites in large proportions of their structures, such as the Boeing 787 Dreamliner, shown in South Carolina as the first one built there is rolled out. (Source: Boeing)
Rob, keeping planes in service longer is certainly one of the benefits hoped for from this new technology. The primary benefits, though, are getting them back into service faster, lower cost, more consistent repairs, and techniques that don't shorten a plane's service life by damaging composites during repair (the lack of force or vibration applied to the structure).
Wow! Thanks for this, Ann. It's often the obvious solutions that are the most frustrating. The use of dirty, violent abrasive cutting techniques on composites is such an obvious no-no when it comes to disturbing the fiber alignment and potential of layer separation in non-damaged portions of the material. I'm guessing previous attempts to cut fiber/resin composites with a high-power laser resulted in either a puddle of goo or a fire. Kudos to Lasertechnik for developing an appropriate combination of laser power, frequency, modulation, and beam profile for use with composites. This will have wide applications.
William, I assume that this technology relies on very precise control of the laser to work. There must be some new advances in laser focus or control to make it possible. It is, becuase of the results you mention, not an obvious choice, but someone has figured out how to make it work (werk?).
Composite repairs cannot be fully checked for quality via visual inspection like conventional repairs. I often wondered how they plan to handle this problem. And well, of course, let a robot do it - they are consistant and have no bad days.
I find it amazing what SLCR Lasertechnik can do with regard to coating removal. They claim, for example, that they can strip the paint from a part while leaving the primer intact. They can also remove paint from selected areas without the need for masking. I can think of a lot of occasions in which the ability to do these things would have been very useful.
By the way, it appears that the company is called SLCR (Selective Laser Coating Removal), not SCLR. The name was misspelled in GKN's press release.
Chuck, Boeing doesn't seem to like to discuss this subject in any detail, so their specific plans are unknown. Since GKN Aerospace is a major supplier to Boeing, one can always make reasonable guesses. That said, Boeing was having a lot of trouble earlier this year with apparent delam issues of the 787's composite fuselage: http://www.latimes.com/business/la-fi-0223-dreamliner-problem-20120223,0,6402954.story
Hey William, glad you liked this story. It does seem kind of 20/20 in hindsight, especially the "don't bang on that complex composite layer" part. The other part that also seems obvious is the crossover from removing coatings on composites via laser--which SCLR Lasertechnik already does, and which sounds like a delicate process--to using lasers to repair composites with what sounds like a very similar method. Maybe someone from SCLR Lasertechnik was having a beer with someone from GKN Aerospace, and one of them said "I wonder what would happen if you used this for that...?" Just a guess.
The art and science of composite repair is constantly evolving. The advent of the B-787 class of aircraft is a game changer. In the past, composite parts have been considered "secondary structures", such as flight control surfaces, landing gear doors, floor panels, etc. Repair procedures were fairly well understood and integrated into the maintenance programs as normal operations. Now, with the composites forming a major portion of the load-bearing structure, the industry has to really step up their game. Our company is one of a few supplying composite repair systems for this purpose. We see every day the struggles the OEMs and the repair activities are having with these issues.
There are really four phases or issues of consideration when repairing composites. 1. Identification of the damage. 2. Preparing the area for repair (removing damaged material). 3. The actual repair (replacement of damaged material) 4. Verification of the process (QA /QC, NDT).
The subject of this article partially addresses #2. A few of the posters flagged some of the issues involved. How practical is the robot for use in-situ scenarios? How well can it negotiate compound curves, fasteners, varying material densities, and unknown sub-strucrures? One poster alluded to "dirty, violent abrasive cutting techniques on composites". Removal of damaged material is actually more surgical, with the use of hand-held routers, die grinders, and the like with diamond and carbide bits designed for this purpose. There is a large human expertise factor required for all phases of composite repair. The application of robotic technology to as many of these processes as possible is laudable, but more development is required. There is as much art as science involved with complex repairs.
Since most composite repairs require the application of heat to cure the aerospace materials, the real challenge is ensuring that heat is uniformly applied and reaches all parts of the material under consideration. This is especially challenging when dealing with carbon-fiber structures. Carbon conducts heat relatively well. The heat wants go everywhere, not just where it is needed. We are actively working with the OEMs to develop equipment and technology to ensure this is possible.
All phases of composite repair have come under much closer scrutiny from the FAA recently. They see the potential for a catastrophic event due to an improperly performed repair. It's back to basics: Training, proper procedures, process control, verification. Welcome to the friendly (safe) skies!
As the 3D printing and overall additive manufacturing ecosystem grows, standards and guidelines from standards bodies and government organizations are increasing. Multiple players with multiple needs are also driving the role of 3DP and AM as enabling technologies for distributed manufacturing.
A growing though not-so-obvious role for 3D printing, 4D printing, and overall additive manufacturing is their use in fabricating new materials and enabling new or improved manufacturing and assembly processes. Individual engineers, OEMs, university labs, and others are reinventing the technology to suit their own needs.
For vehicles to meet the 2025 Corporate Average Fuel Economy (CAFE) standards, three things must happen: customers must look beyond the data sheet and engage materials supplier earlier, and new integrated multi-materials are needed to make step-change improvements.
3D printing, 4D printing, and various types of additive manufacturing (AM) will get even bigger in 2015. We're not talking about consumer use, which gets most of the attention, but processes and technologies that will affect how design engineers design products and how manufacturing engineers make them. For now, the biggest industries are still aerospace and medical, while automotive and architecture continue to grow.
More and more -- that's what we'll see from plastics and composites in 2015, more types of plastics and more ways they can be used. Two of the fastest-growing uses will be automotive parts, plus medical implants and devices. New types of plastics will include biodegradable materials, plastics that can be easily recycled, and some that do both.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.