In addition to repairing composites in aircraft structures, figuring out whether they have been damaged in the first place was a top priority in a GAO report that critiqued the growing use of composites.
We have reported before on this site on self-monitoring adhesives that could predict aircraft structural failures. Now GKN Aerospace, one of Boeing's composite aerostructure suppliers, is researching a class of coatings that may make fractures and other damage visible under certain nonvisible wavelengths.
GKN Aerospace has partnered with a UK university in an 18-month collaborative research venture that's in its first quarter, Max Brown, head of engineering at GKN Aerospace's Filton engineering center, told us.
Inspection of composites used in aircraft such as the A350 XWB, shown here in Getafe, Spain, during
initial horizontal tailplane assembly, may be assisted by research into coatings
that will make damage visible at certain wavelengths.
(Source: Airbus)
"Our collaborative coating research is aimed at supplying inspection techniques for the future maintenance and repairability of composites," said Brown. "Today, it may not be immediately obvious to an inspector of composite material as to what level of damage has been experienced, if any. What we envisage is a more intelligent inspection capability. For example, when inspectors are looking at a wing structure, they could look in the right wavelength range, and any areas that have damage above a certain preset threshold will clearly display that damage."
By the end of the program, GKN expects the coating to reach TRL (technology readiness level) 2 or 3. That would indicate that the research team has proven the basic chemistry and would then be able to move to detailed conversations within the engineering community about development for specific applications. "In an additional 18 to 24 months or so, we would probably be approaching TRL 5 or 6." When a technology reaches TRL 6, it's ready for a demonstration -- in this case, a flight trial.
GKN's goal is to design specific microspheres held within a coating. On impact, if damage has occurred, the microsphere capsule wall fractures, and the chemical reactions produce a signature within the coating that is visible at specific wavelengths.
Thanks for the info, Ann. So that means that the ability to utilize this detection technique will be proprietary, but I guess it also indicates that the state of the technology is at the point where other composite makers should be able to do this too, at least eventually. (That's unless there's only a very narrow class of coatings which are amenable to the detection process, and they're patented or trade secret.) Anyway, I guess the upshot is that this is not going to be anywhere near as industry-widee as I assume. At the same time, it opens up the idea that, with technology advancing, maybe the FAA can move towards some specificity in its composites directives.
TJ, that's funny, using whiteout to detect cracks and delams. I bet it worked great. But I doubt if that would work on CFR composites or even glass-reinforced composites. Damage on these, especially CFR, is invisible to the naked eye and techniques for detecting it different from those used for detecting same in traditional materials. You are right, I carefully did not reveal the wavelength since I honored the company's request in order to get this much published.
You say damage-detecting coatings have been around for awhile, but not using non-visible wavelengths. Do you mean that damage-detecting coatings *for these composites* have been around for awhile? Please inform us if you know!
Alex, thanks for thinking industry-wide again. I agree, the technology is certainly in the early stages and it makes me wonder how many other coatings manufacturers or composite airstructure makers are conducting similar research under the radar, possibly even in partnership with each other. It might make more sense from an industry standpoint to develop and commercialize something that can be applied by all airstructure manufacturers and regulated by the FAA. But that also assumes that it can be applied in an aftermarket scenario and still work properly. I get the impression that GKN's coating needs to be "baked" in, either literally or figuratively, in order to do its job. But that could also be because they are not a coatings manufacturer.
Chuck, someone knows a lot about the subject, and I wish I did. I've already spent quite a lot of time surfing and snooping around on the Web, but it's quite difficult to find out anything aside from what's in that GAO report, and Boeing is less than forthcoming. I assume this is for security and/or market competition reasons. I'm checking the MRO schools' websites for course descriptions, e.g., but not much luck so far. The thing to remember, in general, is that repair techniques have existed as long as composites in aircraft have existed, but for some time it was all military. Then they entered the commercial aircraft sector, but not, I repeat not, in primary structures. Their use in primary structures has changed everything.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
Engineers at the University of California, San Diego are designing a robotic arm that takes inspiration from the loose, flexible, yet very strong structure of the armored plates on a seahorse's tail.
Researchers at the Missouri University of Science & Technology have designed a new nanoscale material that can transmit light faster than the 186,000 miles per second it usually takes to travel through air.
It has often been said that as California goes, so goes the nation. This spring, the state's wind power is setting energy generation records and solar energy generation is expected to rise sharply during the second half of 2013.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
4 
