Regardless of how much carbon fiber composites have entered into car designs such as Audi's, the biggest transportation lightweighting role in the near term will be played by high-performance metals like aluminum and advanced high-strength steel (AHSS), according to a new report from LUX Research. (Source: Audi)
@sjmonte: A joule is a unit of energy, not tensile strength. Tensile strengths are customarily given in units of pascals; one joule per cubic meter is equal to one pascal. However, since one pascal is very small, it's common to use the megapascal, i.e. million pascals, as the base unit.
Could you please give us the tensile strength in either megapascals or pounds per square inch?
In any case, the strength increases you report (more than 2x dry and more than 5x wet) are very impressive. If you have been producing these coupling agents since the 1970s, why haven't they been more widely adopted? I'd expect the composites industry to be extremely enthusiastic about something like this.
Ann: We have exhibited in the past few months at the following conferences and trade shows: ACMA 2012; SAMPE 2012; American Coatings Show 2012; ACS Rubber Division Energy Rubber Group Winter Conference; SPI NPE 2012; and SPE International Polyolefins 2012. So, it's just not fiberglass reinforced polyester. I am talking about all manner of inorganic and organic reinforcements used in thermosets and thermoplastics We manufacture since 1973 organometallic coupling agents based on titanium, zirconim, and aluminum chemistry - rather than silane chemistry. I have 29-U.S. Patents and 1 pending on their composition of matter and their application, and 375-ACS CAS abstracted works on the subject of the interface and their application in polymer compositions.
A class of neoalkoxy and coordinate titanates and zirconates can coordinate couple to any surface via its protons ever present on the inorganic/organic reinforcement - from carbon and aramid fiber to CaCO3 to PTFE - thus forming an impervious 1.5-nanometer chemical bridge between say the carbon fiber and epoxy. The fiber does not have to be pretreated, but can be coupled in-situ becase water of condensation is not needed as with silanes, which react with surface hydroxyls to form a silanol oligomer, which in turn condenses with the surface hydroxyl group to condense 3-moles of water, which must be removed.
The titanate or zirconate uses the resin phase to bring it to the interface and deposit 1.5-nanometer atomic monolayers thus bonding the resin to the reinforcement surface that subsequently resists aged deterioration under high pressure, high temperature, and severe environmental conditions such as 240-hr. water boil in 10% salt water. This mechanism works on all manner of carbonaceous substrates: carbon fiber; carbon black; carbon nano tubes; graphene; etc.
For example, carbon fiber reinforced methyl nadic anhydride cured epoxy composites produced by General Dynamics without zirconate will have a long-fiber tensile strength of 62 Joules, which will deteriorate to 21 Joules 240-hr. water boil in 10% salt water, while 4-parts per thousand of a zirconate [Ken-React(r) NZ(r) 97] added to the epoxy will yield 119 Joules Tensile initial and 113 Joules when similarly water boiled aged.
Actually, fabrication difficulty is mentioned several times in the article, both directly and indirectly, as moldability, disruptive technology vs non-disruptive technology, as "3D components involve a more complicated, expensive molding technology" and "CFRPs are not only more expensive, but using them is also a step change difference, which is much greater than transitioning from using one metal to another metal." Regarding recyclability, it's interesting to note that Boeing has invested in composite recycling: http://www.designnews.com/document.asp?doc_id=235280
I'm not sure what composites you're researching, but they sound like glass fiber. Carbon fiber is another story and answers your strength questions: the strength-to-weight ratio is higher for carbon fiber than steel and even higher than aluminum. Also, I'd bet that any carbon fiber materials you're likely to be able to purchase as a home user are not the ones you can get for building military or commercial aircraft.
The limitation of Carbon and Aramid and Glass reinforced materials - as well as nano-materials - is a lack of awareness of the ability to use zirconate and titanate and aluminate coupling agents to bond the interface of the fiber reinforcement to the polymer resin. Silanes - the material that made the Corvette possible (fiberglass reinforced peroxide cured unsaturated polyester) - have severe interfacial reaction and environmental aging issues due to the nature of their molecular bond formation.
Rob, good point. One of the "features" missing from the article is the fabrication difficulty. In aerospace and some high end applications, where the systems will last a long time, it is worth paying up front for more difficult fabrication. I think it was on this site that a new technique for welding titanium was discussed. This is just one example. Aluminum is also more difficult to weld than steel. Recall that most aircraft, which have used aluminum for a long time, are riveted. Jaguar started making the bodies of their high end XJs of aluminum. When they did that they save 500 pounds (on a 4,000+ pound vehicle). Many wondered if they would ever recover the cost of the production line changes that had to be made. As you mention, steel may end up getting better before price or process technology catches up for the other materials. In addition, steel and aluminum are eaisly recyclable.
BMW has already incorporated more than 10,000 3D-printed parts in the Rolls-Royce Phantom and intends to expand the use of 3D printing in its cars even more in the future. Meanwhile, Daimler has started using additive manufacturing for producing spare parts in Mercedes-Benz Trucks.
SABIC's lightweighting polycarbonate glazing materials have appeared for the first time in a production car: the rear quarter window of Toyota's special edition 86 GRMN sports car, where they're saving 50% of its weight compared to conventional glass.
Design engineers play a big role in selecting both suppliers and materials for their designs. Our most recent Design News Materials Survey says they continue to be highly involved, in some ways even more than the last time we asked to peek inside their cubicles.
Daihatsu is one of the first carmakers to customize car exteriors using 3D printing's mass customization capabilities. Effect Skins -- small exterior bumper and fender panels in different colors and textures -- can be ordered for its Copen convertible.
Several new products in this group of new adhesives, coatings, and sealants are formulated to protect sensitive electronic components, or to seal components of commercial and military aircraft. Others are designed to operate in tough, messy, dirty oil & gas operations, or for rotary applications and motors.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies.
You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived.
So if you can't attend live, attend at your convenience.