UK-based P2i has developed a waterproof nano-coating that protects smartphones such as the Alcatel One Touch, and Motorola's RAZR and XOOM. We think the company should develop the technology for consumers who want to apply it to the devices they already own. (Source: P2i)
I suppose there's a difference between water proof and water resistant. I know there's a difference between fire proof and fire resistant. And it has to do with self extinguishing compared to the inability to catch on fire. In both cases it's intersesting how marketing words sometimes sound similar to what we want, but in the end it's just real close.
I would define immersion as being under water for a few seconds. Dropping it in a bath tub full of water or in the toilet (as one reader described) would be an example. Can this technology withstand that? My guess would be no, because any connection to the outside world would take in water. Right?
Yes, Dave Palmer, I agree. I wasn't suggesting that this process could be marketed as "anti-cancer". I was putting the idea out there. It's a market that's waiting for the right product/attention.
The evidence isn't as weak as those in CE claim though. I'm sure it's not just cell phones placed in bras that has caused increased breast cancer in very young women. What I listended to on Pacifca radio was very compelling and gave good evidence that cell phones aren't entirely benign.
But, is there anything that's completely safe today?
Something that is molecularly bonded can't be peeled off, but ordinary wear takes the surface off anything. How many computer keys have you seen that have become smooth and shiny with age? I am sure that a plastic layer a few nanometers thick is not going to survive any process that takes micrometers off its substrate. Ordinary wear will take this stuff off in very short order. The only things that will remain protected are those that are not subject to wear.
Of course, that is much of the inside of any device.
What does this stuff do to battery contacts and pushbuttons? Is it thin enough to keep its interference to a few milliohms?
I agree with every word of what eafpres wrote. They lost me when they claimed that the coating can never wear off and that it doesn't change the electrical properties of anything. All coatings wear off unless they're extremely hard (e.g. diamaond or SiC), in which case they're hard to deposit, hard to bond, and too brittle for use on even slightly flexible substrates. As for not changing the electrical properties, that means that the coating must "know", based on where it lands, whether it ought to be an insulator or a conductor. That, of course, is impossible.
Furthermore, once moisture gets inside an electronic device, it takes a very long time to get out. That gives it plenty of time to work mischief while it's in there. To really waterproof a camera or cell phone, it's necessary to keep water from getting in. If merely coating the PCBs was sufficient, there are plenty of good conformal coatings that will do that.
My impression is that what happened here is some chemist developed a neat way to put thin hydrophobic coatings on lots of materials, and then let his marketing guy loose with the idea. The marketing guy thought to himself "what's a large market of products that are familiar to the general public that could benefit from waterproofing?", and of course his answer was "cell phones". Unfortunately he knows nothing about electronics or even about manufacturing processes.
This is a great idea - I'm surprised it hasn't come to market sooner. I, for one, could have used this a few years back, when my phone was drowned by the vigorous waves of the Atlantic ocean - blanket too close to the shoreline .... do the math. Of course, it will really be imressive when the technology is made and can be applied to your existing cell phone. Ann, any word from the company on that development?
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
Engineers at the University of California, San Diego are designing a robotic arm that takes inspiration from the loose, flexible, yet very strong structure of the armored plates on a seahorse's tail.
Researchers at the Missouri University of Science & Technology have designed a new nanoscale material that can transmit light faster than the 186,000 miles per second it usually takes to travel through air.
It has often been said that as California goes, so goes the nation. This spring, the state's wind power is setting energy generation records and solar energy generation is expected to rise sharply during the second half of 2013.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 4
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
4 
