NASA is using 3D printing to build engine parts for its next-generation Space Launch System. Shown here is the first test piece produced on the M2 Cusing Machine at the Marshall Space Flight Center. (Source: NASA Marshall Space Flight Center/Andy Hardin)
Thanks, ruffel, glad you liked the article. That's a good question. NASA didn't say what kind, if any, post-sintering processes they're using. They probably haven't figured that out yet, since this is still in the prototype stage.
are these componets used right out of the printer (except the obvious) or do they go through post scintering processes like hot isostatic pressing HIP to improve the density and grain strcture. thanks for a awsome publication
Robespierre, thanks for your comments on nomenclature. As I posted in the comments section of a different article http://www.designnews.com/author.asp?section_id=1392&doc_id=251754 the term "3D printing" is now used, confusingly, to refer to all types of additive manufacturing. One of the reasons for this is no doubt the fact that the term "3D printing" gets a lot more attention than the term additive manufacturing, probably because it's immediately easier to visualize what's meant, at least by those not familiar with AM. It's also true that much of the actual 3D printing done in the beginning of that version of AM used (and uses) inkjet technology, very similar to the printers that sit on our desks, so it's a valid term for that sector of AM. I'm not sure what you mean by "these types of parts have been manufactured via additive manufacturing for years." NASA using AM to make rocket engine parts is pretty darn revolutionary.
Cabe, the term "3D Printing" only confuses people, doesn't explain the various technologies and is a very weak term to encapsulate an entire industry. Supposedly, the term "3D Printing" was supposed to replace the term "Rapid Prototyping" and does a weak job at it because people assume the machinery are printers, such as some cheap thing sitting on a desk. The more powerful term is "Additive Manufacturing" and encapsulates the host of part producing technolgies with strength. Some Additive Manufacturing technologies produce plastic parts i.e. made in Nylon; ABS; Acrylic, etc. and some of these parts are perfectly fine for use as a Rapid Manufactured functional part and are present on space aircraft to this day. Within the Additive Manufacturing industry exist systems that produce parts in metal, layer by layer, and the parts go directly into the human body, or into jet engines. Turbine blades for commercial aircraft are made directly in a select couple of additive manufacturing technologies, with the welds being stronger than the titanium itself. Some parts require the HIP (Hot Isostatic Process) prior to final stamp of approval, but nonetheless, they are functional parts ready for installation. The article here is factual, with the only exception that these types of parts have been manufactured via additive manufacturing for years. It is not new news within the industry but is now coming out as giant leaps in the additive manufacturing metals process has now become better, cheaper and faster.
You probably aren't aware that 3D printing of titanium hip replacements have already captured a large percentage 30%? of the market already. They leave the structure somewhat porous so that the bone can actually grow into it. CT scans are used to create the 3D model used to make the part specifically for your joints. What a great use of this process!
You raise a number of good points, William K. I, too, was impressed by the fact that NASA would consider this process for a functional part. This could be a sign that 3D printing is finding its niche in low-production-volume parts.
A tiny humanoid robot has safely piloted a small plane all the way from cold start to takeoff, landing and coming to a full stop on the plane's designated runway. Yes, it happened in a pilot training simulation -- but the research team isn't far away from doing it in the real world.
Some in the US have welcomed 3D printing for boosting local economies and bringing some offshored manufacturing back onshore. Meanwhile, China is wielding its power of numbers, and its very different relationships between government, education, and industry, to kickstart a homegrown industry.
You can find out practically everything you need to know about engineering plastics as alternatives to other materials at the 2014 IAPD Plastics Expo. Admission is free for engineers, designers, specifiers, and OEMs, as well as students and faculty.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.