First Civil Jet Flies on 100 Percent Non-Food Biofuel
11/7/2012
Canada's National Research Council and the Canadian Space Agency have used the Falcon 20 jet, with modified hydraulic and aircraft fuel systems, for performing parabolic flight maneuvers in microgravity experiments. (Source: Canadian Space Agency)
As Mydesign asked earlier, what's the cost? Fuel cost is an airline's biggest expense. How much will these biofuels save them? If there's no savings, there's no way they will adopt its use. I hope taxpayers won't have to subsidise this like the current $2.21/gal hidden tax we're getting stuck with using ethenol blends in our cars.
Nice article, Ann. This test flight is good news no matter where the biofuel comes from. It's a step is a positive direction. Different crop growers will experiment with crops that match efficiency and regulation as they move on and expand biofuels programs.
Lou, thanks for the clarification. The fact that not all semi-arid areas are found between those two Tropics plus the fact that wild mustard grows in semi-arid areas in the SF Bay Area tells us that the plant family can grow wild outside of the "tropics" as you've defined them. Even more likely when engineered by humans in one way or another. Maize (corn) is a perfect example: it began as a radically different plant in Mexico and several hundreds of years later was cultivated in astonishing variety all the way from the tropics to the Northern Plains. So I'm not sure why you conclude that this plant is not suited to the Canadian climate.
Ann, thanks for the clarfiication. By tropic I mean the area between the Tropic of Cancer and the Tropic of Capricorn, not necessarily a wet area. This is where a lot of, but not all, of the type of land that might be useful for this crop. It still doen not correspond with any area of Canada, which is interesting. They have plenty of oil and lots of land. I would have thought they would be looking at crops appropriate to their climate.
Mydesign, specific prices were not mentioned, but the fact that this is a crop being grown industrially in large quantities bodes well. Applied Research Associates says the ReadiJet fuel is "low cost" due to the catalytic hydrothermolysis process, http://www.ara.com/fuels/CH-Technology-Status.html which "provides a net cost savings compared to straight hydrotreating and hydrocracking processes. The cost savings result from the reduction of hydrogen and catalyst cost consumption and the production of high-value chemicals." To me, what's most important is the fact that this fuel's performance is good enough to work unblended.
Lou, it's not tropical areas where these Brassica plants and their relatives grow, which would be much too moist, but arid and semi-arid regions, many of which are near the equator. Brassica carinata, the one described in the article, is also called Ethiopian mustard, for instance. A variety of wild mustard even grows in the foothills of the San Francisco Bay Area every spring on very poor, dry, non-irrigated soil used for horse and cattle pastures. The point is, it does not compete with agricultural crops, which aren't grown, or likely to be grown, on the same poor soil where the Brassica grows. There are several species with these characteristics being considered or used for biofuel.
Ann, I find it interesting that Canada is looking at these crops. They generally only grow in tropical, or semi-tropical, regions. One that I am familiar with is jatropha. While it is being used, and is touted as a plant that can be turned into aviation fuel, its impact is very small.
Another issue with any crop that is grown on land is that, although the crop is not a food crop, it can compete with food crops for land. Algae and seaweed do not have this problem.
Ann, aviation fuels are the purest form of crude oil with a higher cost. So any alternate to crude oil based aviation fuel will have a greater impact on aviation sector. What about the cost factor?, if cost is less than crude oil, then obliviously it will helpful for the low cost carriers.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
Engineers at the University of California, San Diego are designing a robotic arm that takes inspiration from the loose, flexible, yet very strong structure of the armored plates on a seahorse's tail.
Researchers at the Missouri University of Science & Technology have designed a new nanoscale material that can transmit light faster than the 186,000 miles per second it usually takes to travel through air.
It has often been said that as California goes, so goes the nation. This spring, the state's wind power is setting energy generation records and solar energy generation is expected to rise sharply during the second half of 2013.
The latest model of Liquid Robotics' Wave Glider autonomous, unmanned marine vehicle (UMV), the SV3, is reportedly the world's first hybrid wave- and solar-power-propelled unmanned ocean robot.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
