A wheel made of metal and plastic designed to fit the 2012 MYFord Focus SE has shown an increase of 1.1 MPG highway in third-party tests, compared to the car's standard production wheel. That's comparable to MPG improvements made by some low-roll tires.
Lacks Wheel Trim Systems' eVOLVE Hybrid Wheel mixes an aluminum structure with a foam filling and a plastic coating. The structure is made of A356-T6 low-pressure cast aluminum alloy, James Ardern, director of business development, told Design News. This is the same aluminum grade, and manufactured by the same low pressure cast process, as the Ford Focus BM5J-1007-DB production wheel. The wheel's outer shell is made of a high-impact polycarbonate/ABS composite blend, which allows a more aerodynamic design, Ardern told us. Between the outer shell and the five-spoke aluminum structure is a high-density, two-part urethane foam, instead of more aluminum.
The eVOLVE Hybrid Wheel made of metal and plastic, designed for the 2012 MYFord Focus SE, has shown an increase of 1.1 MPG highway in third-party tests, compared to the car's standard production wheel. (Source: Lacks Wheel Trim Systems)
Lacks tested its eVOLVE Hybrid Wheel, as well as two other wheels, on a North American 2012 MYFord Focus SE on the same day and the same test track. The other two wheels were the eVOLVE wheel's backbone, without its foam filling or coating, and the Ford Focus production wheel. All three are the same dimensions: 17 inch x 7 inch x 50 mm offset. The production wheel weighs 23.7 lb; the backbone alone weighs 17.4 lb, and the complete eVOLVE Hybrid Wheel, including backbone, foam, and composite coating, weighs 19.2 lb.
On-vehicle fuel economy testing was done to EPA standard SAE J2263 by third-party testing facility Roush Emissions Laboratory, which does the same EPA drive cycles for automotive OEMs. The backbone showed some improvement over the production wheel's fuel efficiency. "But it was less of a difference: increases of 0.1 MPG city and 0.5 MPG highway," said Ardern. Using the complete eVOLVE wheel, city improvement was 0.4 MPG, and highway, 1.1 MPG.
Weight reduction alone isn't enough to achieve those results. The other main factor is the eVOLVE wheel's improved aerodynamics. Lacks performed wind tunnel testing of several hybrid wheel designs at third-party aerodynamics testing facility Aerodyn, a NASCAR lab. Lacks then selected the best performing wheel design as the eVOLVE Hybrid Wheel for further testing, Ardern told us.
Compared to the Ford Focus production wheel, in static and rotating aerodynamics testing done to EPA standard SAE J2264 the winning eVOLVE wheel design had an overall vehicle drag coefficient improvement of nine counts. "The reduction of aero drag as well as a reduction in aero horsepower both contribute to the optimized aerodynamic profile, and ultimately to fuel economy performance," said Ardern.
cookiejar, I had a similar thought when researching this article--how incredibly complex the process is of analyzing all the variables and how they interact. Thanks for the input on the Citroen wheels. Interesting to know that such design considerations--aerodynamics and materials--were being looked at back then. I wonder if that's the Citroen model my husband and I rented in France in 1974.
Speaking of aerodynamics, both the Citroen SM and the (1954 - 1972) DS featured full and smooth wheel covers. Brake cooling was by separate ducts to inboard transaxle mounted disc brakes. Brake fade was unmeasrable. Interestingly, with front wheel drive, the very reliable CV drive shafts took the full force of braking - much higher than engine output. These FWD transaxles and components were a favorite of formula 1 cars for many years when used in the rear.
I find the engineering of Citroen awe inspiring because they certainly marched to a different drummer well ahead of the mob. The Citroen DS, which has more leg and head room than my 4050 lb Buick Lucerne weighed in at an amazing 2700 lbs. The current Fiat 500 weighs in at 2600 lbs. With its self adjusting air/hydraulic suspension, the DS rode perfectly under all loads, superior to my 2007 Lucerne CXS's magnetic ride.
The Citroen SM, introduced in 1972 had composite wheels as an option, but they really didn't catch on. Citroen was also known for its low drag aerodynamic designs tested in its wind tunnel that had a moving conveyor belt, as they maintained that the interface between the car bottom and the road had the greatest wind shear and hence presented the greatest drag. All Citroens, including the ugly 2CV had very smooth bellies.
If weight is important in the wheel tire assembly, then perhaps tire weight deserves another look. I've noticed incredible weight differences between different tires of the same size. I've also noticed that the heavier tires really bounce when dropped. Unsprung weight has significant effects on handling on uneven surfaces as well as ride.
The latest fashion for low profile tires reduces the amount of rubber and air cushion and increase the amount of rim.
Thank you Ann for inviting us to provide additional information here. There have been some excellent and insightful comments made by the readers and clarification is always good for both parties. If further information is required, your readers can visit us at www.evolvehybrid.com or stop by booth 325 at the upcoming SAE World Congress in Detroit, April 16-18 for a first hand look at the eVOLVE hybrid wheel.
Thanks to Lacks (James, I believe that's you commenting here) for weighing in on the testing issues, as well as giving us more info on the design tradeoffs between aerodynamics, cooling and esthetics issues.
Our testing shows that completely covering the wheel achieves better aerodynamics, that said cooling and design is compromised so it is not a realistic option. Wheels are as emotional as they are functional – especially considering the side on visual impact of the vehicle. The eVOLVE hybrid wheel philosophy is to balance, weight, aerodynamics, design and finishes all at the same time. We believe composite wheel technology provides the ultimate method to balance all attributes as best possible.
The Lacks composite wheel system has been proven with over 24 million wheel assemblies delivered to OEM's globally over the past 15 years. There have been virtually no field issues due to excessive brake heats from disc or drum brake systems. We routinely test our Chromtec wheels on-vehicle through the Death Valley Brake Fluid Boil protocols and also through similar on-vehicle high brake heat exposure testing through the Gros-Glockner drive route in Europe. These tests are used by most of the global OEM's to evaluate wheel products and technologies for durability and reliability. The Lacks composite is approved for virtually all production vehicle applications and its designs are intended to provide both sufficient cooling to the brake system and optimized weight and aerodynamic performance to the overall vehicle system itself...achieved through great design.
Our experience is that fuel efficiency related to automotive wheels is a relatively unexplored area of technology, although efforts have been focused on mass and inertia...as well as aerodynamics. The eVOLVE hybrid wheel is one of the first programs to focus on good wheel design from a structural and aerodynamic perspective, relative to the impact on fuel economy itself. Previously, most efforts considered either mass or aerodynamics seperately and usually for some attribute other than fuel economy. We believe the eVOLVE philosophy will greatly assist the OEM's in their efforts to improve fuel economy without sacrificing great design. The results and video showing the coast down and wind tunnel testing are available at www.evolvehybrid.com.
You're right, sensor_pro, and all of the automakers are already doing everything you mentioned here and more. Automotive engineers are looking at everything in an effort to get to 54.5 in the next 12 years. If they could find about 25 more things that improve mpg like this does, they'd be on the verge of success. The big question, though, is how much will all of these improvements cost? If we have to load the vehicle with composites and other lightweight materials, and the cost gets driven up by a factor of two or more, they're going to find a lot of consumers holding onto their old cars.
bobjengr, I agree about incremental developments. While it's easy to wish we could just figure out and execute/implement everything all at once, real life tends not to work that way.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
Engineers at the University of California, San Diego are designing a robotic arm that takes inspiration from the loose, flexible, yet very strong structure of the armored plates on a seahorse's tail.
Researchers at the Missouri University of Science & Technology have designed a new nanoscale material that can transmit light faster than the 186,000 miles per second it usually takes to travel through air.
It has often been said that as California goes, so goes the nation. This spring, the state's wind power is setting energy generation records and solar energy generation is expected to rise sharply during the second half of 2013.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
4 
