Engineering Materials
Metal/Plastic Car Wheel Boosts MPG

The eVOLVE Hybrid Wheel made of metal and plastic, designed for the 2012 MYFord Focus SE, has shown an increase of 1.1 MPG highway in third-party tests, compared to the car's standard production wheel.  (Source: Lacks Wheel Trim Systems)
The eVOLVE Hybrid Wheel made of metal and plastic, designed for the 2012 MYFord Focus SE, has shown an increase of 1.1 MPG highway in third-party tests, compared to the car's standard production wheel.
(Source: Lacks Wheel Trim Systems)

Return to Article

View Comments: Newest First|Oldest First|Threaded View
<<  <  Page 3/4  >  >>
Ann R. Thryft
User Rank
Re: Huge improvement
Ann R. Thryft   2/11/2013 8:02:21 PM
tekochip, one of the things that made me want to write about this wheel design was the fact that in other stories about alternative wheel materials some have commented about how much aerodynamics, as well as less weight from lighter materials, could add up to better performance.

Ann R. Thryft
User Rank
Re: Huge improvement
Ann R. Thryft   2/11/2013 7:56:06 PM
Thanks for weighing in, Chuck. The amount of MPG saved is one of the main things that attracted me to write about this. Also the fact that these guys have done their homework with 3rd-party testing, and at the same facilities, as automotive OEMs.

User Rank
bobjengr   2/11/2013 6:12:23 PM
Excellent Post--I think this is the way highway mileage improvement will occur-in an incremental fashion.  I know from previous posts, automotive companies are working on many projects to meet the new Federal guidelines coming quickly.  I have been following with great interest materials that are lighter yet as strong as ones now being used.  I feel the metal/plastic wheels represent a great breakthrough. 

User Rank
always a compromise.....
Thinking_J   2/11/2013 5:02:36 PM
The compromise: reduced cross flow = less cooling of brakes.

On most consumer cars the impact would likely be minimal.

On my car.. well, let's just say I like "spirited" driving on mountain roads.

At "Indy" a number of years ago.... they were noting other trade offs relating to the wheel design. Specifically the affect on handling at high speeds when the wheel was optimized for minimal drag, the wheels would start acting like forward "rudders" during high speed turns - making suspension tuning kinda weird.



User Rank
Way too much waste
Rigby5   2/11/2013 3:38:37 PM
While lighter wheels are nice, what I would prefer to see instead is for cars to get rid of all the electric motors for seats, door locks, windows, heat controls, etc.

Manual operations not only weight far less, but are far more reliable and cheaper to maintain.  If customers were actually told that things like keyless entry and remote start required leaving radio receivers on all the time, I doubt anyone would actually still want these silly features.

Elizabeth M
User Rank
News to me
Elizabeth M   2/11/2013 11:55:53 AM
Thanks for covering this, Ann. While power-train and alternative fuel research is well-known and well-covered, I had no idea research into wheels also was being done to boost MPG on automobiles. It's quite interesting to read about and I am consistently impressed by the multifaceted work designers and engineers are doing.

User Rank
Re: Ford F150 also
GTOlover   2/11/2013 10:51:31 AM
Here is the F 150 wheel:


It is the same manufacturer as the Focus wheel described here at DN.

User Rank
New design using Old Ideas
RaceCarBuilder   2/11/2013 10:50:00 AM
The three-piece modular wheel is even lighter. A 15" dia 10" wide Jongbloed wheel from the mid- '70s weighed 14 lbs. It used two spun aluminum wheel halfs and a forged magnesium center. This was a racing wheel so it was plenty strong but it was difficult to maintain-- dogs would come from adjacent counties to pee on mag wheels!

As far as aerodynamics are concerned, Bonneville racers have used "Moon Discs" since the '50s to improve the rotating and wind resistance of their wheels. These are spun aluminum discs that cover the center of a standard steel wheel. They are still used in land speed racing. They do not allow brake cooling air circulation, however.

Instead of such a complex wheel structure as this new wheel design, why not just mould that design with a carbon fiber reinforced polymer?

Deja vu all over again.

User Rank
I thought plastic wheel dressings were gone in the 90s
Eric75   2/11/2013 9:44:34 AM
Unsprung mass is a big deal for vehicle performance although not necessarily fuel economy. Reduced rotating inertia probably has an impact on city driving more than taking weight out of the seat frames. I wonder how much the plastic is about appearance rather than aerodynamics. Wheels take a beating, and I know they will look pretty bad by the time I buy a 2014 focus in the year 2025.

User Rank
Cost Benefit
Tim   2/10/2013 7:46:25 PM
If I read the article correctly, the metal/plastic wheel is about 4 pounds less than the standard wheel. For this weight reduction, is there a cost savings or is the main benefit the MPG increase?

<<  <  Page 3/4  >  >>
Partner Zone
More Blogs from Engineering Materials
NASA's MAVEN spacecraft has entered Mars' atmosphere, carrying instruments to help Earthlings figure out what happened to it. Launched last November, the spacecraft arrived at the red planet right on time after a journey of 442 millionmiles.
More bioplastic materials have entered the 3D-printable filament fray. These PLA formulations reinforced with wood or bamboo fibers will debut at the October Composites Europe show in Germany.
Airbus Defence and Space has 3D printed titanium brackets for communications satellites. The redesigned, one-piece 3D-printed brackets have better thermal resistance than conventionally manufactured parts, can be produced faster, cost 20% less, and save about 1 kg of weight per satellite.
At IMTS last week, Stratasys introduced two new multi-materials PolyJet 3D printers, plus a new UV-resistant material for its FDM production 3D printers. They can be used in making jigs and fixtures, as well as prototypes and small runs of production parts.
GE Aviation not only plans to use 3D printing to mass-produce metal parts for its LEAP jet engine, but it's also developing a separate technology for 3D-printing metal parts used in its other engines.
Design News Webinar Series
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 20 - 24, How to Design & Build an Embedded Web Server: An Embedded TCP/IP Tutorial
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: October 1 - 30
Sponsored by Gates Corporation
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service