As we showed you in a recent slideshow, some NASA scientists envision astronauts making whatever they need out of local materials on Mars or the moon via 3D printing. While technology from organizations like Contour Crafting has made this theoretically possible, now, Washington State University (WSU) engineers have actually used moon rocks to print some simple-shaped objects -- on Earth.
Real moon rocks are too rare, so researchers are using an imitation moon rock called lunar regolith simulant. Regolith is a mixture of loose dust, rock, and soil that covers solid bedrock on earth, as well as other planets, the moon, and some asteroids. The simulant is formulated to approximate the real lunar regolith's chemical and mineral properties. There are several versions. The WSU team used about 10 lb of one version that contains silicon, aluminum, calcium, iron, and magnesium oxides.
Washington State University engineers have 3D-printed some simple-shaped objects using a simulant of lunar regolith, a mixture of loose dust, rock, and soil that covers solid bedrock. Shown here, Apollo 16 astronaut Charlie Duke drives a core sample tube into the lunar regolith. (Source: NASA)
A team that includes Amit Bandyopadhyay and Susmita Bose, professors at the university's School of Mechanical and Materials Engineering, has demonstrated the printing of parts from the raw, artificial moon rock. NASA is working with several organizations, including Contour Crafting, to develop the technology for fabricating simple tools or replacement parts, but Bandyopadhyay's group is the first to demonstrate the ability.
Previously, Bandyopadhyay and Bose had used 3D printing to create bone-like materials for use in orthopedic implants. Their current work uses Laser Engineering Net Shaping (LENS) technology, specifically, LENS-750 systems. These are based on laser sintering, the most common additive manufacturing method. The team published its results in an article in the Rapid Prototyping Journal.
According to the article abstract, the team produced dense parts with no macroscopic defects, which they characterized to evaluate how laser processing affected the lunar regolith simulant's microstructure, constituent phases, and chemistry. Characterization was done using X-ray diffraction, differential scanning calorimetry, scanning electron microscope, and X-ray photoelectron spectroscopy.
Although the laser processing did cause marginal changes in the material's composition, after some trial and error, the researchers managed to produce parts that did not crack when they solidified.
The team has sent its results to NASA. Other team members include Vamsi Krishna Balla, also with WSU's School of Mechanical and Materials Engineering; Luke B. Roberson, of NASA's Kennedy Space Center; Gregory W. O'Connor, of Amalgam Industries; and Steven Trigwell, of ASRC Aerospace Corp. The research was supported by a $750,000 W.M. Keck Foundation grant.
In the video below, Bandyopadhyay shows the regolith material and explains that the technology can also be used onsite to repair broken parts. The achievement, he says in the video, is a first-generation work that will probably not be ready for commercial use for another 50 years or so.
I suspect it may not take that long, considering how fast this technology area is advancing. NASA is already working on 3D printing rocket engine parts, and other researchers have figured out how to 3D print entire personal electronic devices. The two biggest challenges in printing objects from moon rocks seem to be figuring out the best combination of laser sintering processing and moon rock material, plus, making small printers that will work in a zero-gravity environment.
Didn't know that printing on the Moon or Mars would require working in a "zero gravity" environment. Low gravity, as compared to earth maybe, but not zero gravity. If you are going to be making stuff to be used on the surface it would make no sense to transport it to space and then back to the surface as that would have a heavy cost in fuel that would be in short supply.
Lunar Regolith sounds a lotlike moon dust, which should be available in adequate quantities on the moon, it seems.
What are the mechanical properties of the parts fabricated thus far, and are they actually useable? I know that the first 3D printed parts were primarily useful for visualizing and not much else. But tha was in 1988.
Producing parts from the materials listed does not seem like they would be very tough, but rather very hard and quite brittle, unless some additional work was done on the mixture prior to laser sintering. I see a real challenge in providing a uniform particle size and uniform chemical composition.
Providing enough power to run the 3D printer is the other challenge that could be an obstacle to using the process onthe moon, although with an adequate solar array enough power should be available.
If more information is available a discussion of the properties of the material will be an interesting presentation indeed.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
Researchers at the Missouri University of Science & Technology have designed a new nanoscale material that can transmit light faster than the 186,000 miles per second it usually takes to travel through air.
It has often been said that as California goes, so goes the nation. This spring, the state's wind power is setting energy generation records and solar energy generation is expected to rise sharply during the second half of 2013.
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is