HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Engineering Materials

Aerospace Fasteners Mix It Up

NO RATINGS
Page 1 / 3 Next >
View Comments: Oldest First|Newest First|Threaded View
TJ McDermott
User Rank
Blogger
Repairs of composites
TJ McDermott   11/8/2012 10:30:47 AM
NO RATINGS
Ann, while composites may cause fewer fasteners to be used in original manufacture, I would expect their use to be undiminished for composite repairs.

Ann R. Thryft
User Rank
Blogger
Re: Repairs of composites
Ann R. Thryft   11/8/2012 12:31:07 PM
NO RATINGS
That's true of course. The question is, given an increase in composite use, whether fasteners will be used in high enough quantities in repair to make up for the lower overall quantities in manufacturing.

ttemple
User Rank
Platinum
Where is the picture?
ttemple   11/8/2012 3:58:21 PM
NO RATINGS
Ann,

Is that picture from Textron in Nashville?

 

Ann R. Thryft
User Rank
Blogger
Re: Where is the picture?
Ann R. Thryft   11/9/2012 12:16:51 PM
NO RATINGS
ttemple, my sources did not divulge the locations of the aircraft assembly photos, probably due to customer NDA requirements. But feel free to guess!

bobjengr
User Rank
Platinum
Aerospace Fasteners
bobjengr   11/11/2012 2:38:46 PM
NO RATINGS
 

Excellent post Ann.  I know the longevity of any fastener is dependent upon the application and use.  Relative to composite fasteners, do we know how they "stack up" relative to metal fasteners?  I have seen no data that tries to correlate life cycles of either type.  Great point also about the grounding of composites.  I know this must be a huge issue but not talked about too much in the literature. 

Ann R. Thryft
User Rank
Blogger
Re: Aerospace Fasteners
Ann R. Thryft   11/12/2012 11:56:51 AM
NO RATINGS
Glad you liked the article. The whole issue of the grounding of composites used in aircraft has been widely misunderstood, so I thought it was a good idea to include some clear discussion on that issue. Could you clarify your question about comparisons between fasteners for composites and fasteners for metal? What sort of comparisons do you have in mind?

Cabe Atwell
User Rank
Blogger
Re: Aerospace Fasteners
Cabe Atwell   11/21/2012 4:13:58 PM
NO RATINGS
I never thought that lightening strikes on aircraft was so common. I read that it happens 2 times per year on average, per airplane. I have seen electrical discharge responsible for fastener loosening and in some cases, ejecting.  

There is a downside to composite pieces, price. Bolting parts together will always be around. I designed a mechanical system that ended up having over 60 bolts.. it was cheaper than with none, that was for sure.

C

http://usatoday30.usatoday.com/travel/columnist/getline/2005-08-29-ask-the-captain_x.htm

Ann R. Thryft
User Rank
Blogger
Re: Aerospace Fasteners
Ann R. Thryft   11/26/2012 12:03:55 PM
NO RATINGS
The lightning strike issue isn't about frequency so much as it is about catastrophic results. If you've only got a (for example) 1% chance of something happening, but that something has catastrophic results--people dying, lawsuits--then that's something you've got to protect against, or at least not encourage, in your materials and assembly process selection.

Partner Zone
More Blogs from Engineering Materials
To give engineers a better idea of the range of resins and polymers available as alternatives to other materials, this Technology Roundup presents several articles on engineering plastics that can do the job.
The first photos made with a 3D-printed telescope are here and they're not as fuzzy as you might expect. A team from the University of Sheffield beat NASA to the goal. The photos of the Moon were made with a reflecting telescope that cost the research team 100 to make (about $161 US).
A tiny humanoid robot has safely piloted a small plane all the way from cold start to takeoff, landing and coming to a full stop on the plane's designated runway. Yes, it happened in a pilot training simulation -- but the research team isn't far away from doing it in the real world.
Some in the US have welcomed 3D printing for boosting local economies and bringing some offshored manufacturing back onshore. Meanwhile, China is wielding its power of numbers, and its very different relationships between government, education, and industry, to kickstart a homegrown industry.
You can find out practically everything you need to know about engineering plastics as alternatives to other materials at the 2014 IAPD Plastics Expo. Admission is free for engineers, designers, specifiers, and OEMs, as well as students and faculty.
Design News Webinar Series
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 20 - 24, How to Design & Build an Embedded Web Server: An Embedded TCP/IP Tutorial
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: 10/28-10/30 11:00 AM
Sponsored by Stratasys
Next Class: 10/28-10/30 2:00 PM
Sponsored by Gates Corporation
Next Class: 11/11-11/13 2:00 PM
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service