HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
REGISTER   |   LOGIN   |   HELP
Blogs
Engineering Materials

Joining Techniques Critical to Auto Composites

NO RATINGS
Page 1 / 2 Next >
View Comments: Threaded|Newest First|Oldest First
Rob Spiegel
User Rank
Blogger
Will adhesives hold over time?
Rob Spiegel   8/22/2012 1:22:20 PM
NO RATINGS
Fascinating story, Ann, on how to join materials that can't be welded. One thing that gives me pause is that as they develop appropriate adhesives, it will still only be a guess on how the joining materials will hold up after 20 years. Only time will tell whether the adhesives will hold the car together over decades.

 

Ann R. Thryft
User Rank
Blogger
Re: Will adhesives hold over time?
Ann R. Thryft   8/22/2012 3:27:18 PM
NO RATINGS
These are structural adhesives, and many of them are being adapted from aerospace applications, where they've been used with composites for some time. We covered structural adhesives here
http://www.designnews.com/document.asp?doc_id=237011

Rob Spiegel
User Rank
Blogger
Re: Will adhesives hold over time?
Rob Spiegel   8/22/2012 3:34:10 PM
NO RATINGS
That link gives good information on adhesives, Ann, especially in the area of the advantages of adhesives over fasteners. 

ttemple
User Rank
Platinum
Re: Will adhesives hold over time?
ttemple   8/22/2012 3:59:10 PM
NO RATINGS
I did some work at Raytheon (Beech) quite a number of years back.  They routinely used adhesives to bond aluminum aircraft parts together.  The parts were also riveted (sparingly), but the engineers referred to the rivets as "chicken rivets", because they insisted the glue was more than strong enough. Supposedly the FAA wouldn't let them get rid of all of the rivets.  I don't know how it ages, however.  We had to disassemble some of the parts that were glued, and the aluminum would tear before the glue would let go.  As I remember it, the stuff was basically inseparable.

Rob Spiegel
User Rank
Blogger
Re: Will adhesives hold over time?
Rob Spiegel   8/22/2012 4:18:20 PM
NO RATINGS
That's very encouraging, Ttemple. Was that a number of years ago? I would guess if adhesives had any durability problems we would know by now. In manufacturing, I would think using adhesives is more efficient than welding.

ttemple
User Rank
Platinum
Re: Will adhesives hold over time?
ttemple   8/23/2012 11:45:53 AM
NO RATINGS
Rob,

I would say around 1996 or so.  They were manufacturing the (Kingair?)"1900D" heavily at that time.  It says on wikipedia that the 1900D was introduced in 1991, and produced through 2002.  I'm sure that many 1900D's are still in use as regional commuters.

I don't know when they started using adhesives though.  The part I remember specifically was the window attachment to the fuselage skin.  There was sort of an aluminum porthole looking piece that was glued to the fuselage.  The joint had the appearance of a weld, and it held together like it.

I think they use adhesives in the wing compartments too, at least in the areas where there is going to be fuel stored.  The adhesives seal the compartments, I think.  They also use special fuel resistant coatings on the skin inside those areas.

Rob Spiegel
User Rank
Blogger
Re: Will adhesives hold over time?
Rob Spiegel   8/23/2012 1:43:31 PM
NO RATINGS
Ttemple, it sounds like there is an good long track record on the adhesives, at least a couple decades. So, while these adhesives may be new to the auto industry, they seem to be well tested in aerospace.

Ann R. Thryft
User Rank
Blogger
Re: Will adhesives hold over time?
Ann R. Thryft   8/23/2012 12:07:51 PM
NO RATINGS
ttemple, thanks for telling us about your direct experience. Anything going into the construction of commercial aircraft has very strict specifications and requirements, including extensive testing on the ground and in the air, and everything is 100% traceable. Whether structural adhesives or fasteners are used in a particular part of the plane depends on several factors, but stresses in aircraft are much more extreme than in cars.

William K.
User Rank
Platinum
Adhesives: How long will I be "stuck on you"?
William K.   8/23/2012 9:39:49 PM
NO RATINGS
It certainly is a valid question, adhesive lifetime, and how does one speed the aging process so as to find a correct answer? And the very important question is how reliableare the bond lifetime results? Many adhesives primarily fail through long term creep type of fault, while in others t6he ridgid bond becomes brittle and does not stand up to shocks. Two different failure mechanisms, it seems. And he experience of how things stick to a composit is not the level that we are looking for.  So the solution is to understand the failure mechanism, and use that information.

Ann R. Thryft
User Rank
Blogger
Re: Adhesives: How long will I be "stuck on you"?
Ann R. Thryft   8/28/2012 12:54:10 PM
NO RATINGS
A lot of research has been done on structural adhesives, as we've covered here http://www.designnews.com/document.asp?doc_id=237011 and here http://www.designnews.com/document.asp?doc_id=236816 Fabrico, which doesn't make adhesives, but uses them assembling all kinds of structural components, has articles and a Q&A on many of these subjects here http://fabricoforum.com/2012/06/structural-adhesives/

Partner Zone
More Blogs from Engineering Materials
NASA and Boeing developed a huge, carbon composite cryogenic fuel tank for deep space missions, and started testing it last month. The 18-ft cryotank will enable heavy-lift launch vehicles to send both humans and robots into deep space.
German engineering firm EDAG Group showed a single-piece, 3D-printed car body design inspired by a turtle at the Geneva Motor Show. It came about after an assessment of how additive manufacturing could be applied to making industrial components, modules, and complete vehicle bodies.
Stratasys is buying assets of a key player in materials testing and R&D for its FDM filament printers, and there's a new polypropylene material for the PolyJet series of 3D printers.
3D printing has met up with drones in a 3D-printed UAV. University of Sheffield engineers printed the prototype drone in 24 hours from ABS plastic using Fused Deposition Modeling.
Some of the biggest self-assembled building blocks and structures made from engineered DNA have been developed by researchers at Harvard's Wyss Institute. The largest, a hexagonal prism, is one-tenth the size of an average bacterium.
Design News Webinar Series
3/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
2/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
12/18/2013 Available On Demand
11/20/2013 Available On Demand
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Apr 21 - 25, Creating & Testing Your First RTOS Application Using MQX
SEMESTERS: 1  |  2  |  3  |  4  |  5


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: April 29 - Day 1
Sponsored by maxon precision motors
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service