A wheel made of metal and plastic designed to fit the 2012 MYFord Focus SE has shown an increase of 1.1 MPG highway in third-party tests, compared to the car's standard production wheel. That's comparable to MPG improvements made by some low-roll tires.
Lacks Wheel Trim Systems' eVOLVE Hybrid Wheel mixes an aluminum structure with a foam filling and a plastic coating. The structure is made of A356-T6 low-pressure cast aluminum alloy, James Ardern, director of business development, told Design News. This is the same aluminum grade, and manufactured by the same low pressure cast process, as the Ford Focus BM5J-1007-DB production wheel. The wheel's outer shell is made of a high-impact polycarbonate/ABS composite blend, which allows a more aerodynamic design, Ardern told us. Between the outer shell and the five-spoke aluminum structure is a high-density, two-part urethane foam, instead of more aluminum.
The eVOLVE Hybrid Wheel made of metal and plastic, designed for the 2012 MYFord Focus SE, has shown an increase of 1.1 MPG highway in third-party tests, compared to the car's standard production wheel. (Source: Lacks Wheel Trim Systems)
Lacks tested its eVOLVE Hybrid Wheel, as well as two other wheels, on a North American 2012 MYFord Focus SE on the same day and the same test track. The other two wheels were the eVOLVE wheel's backbone, without its foam filling or coating, and the Ford Focus production wheel. All three are the same dimensions: 17 inch x 7 inch x 50 mm offset. The production wheel weighs 23.7 lb; the backbone alone weighs 17.4 lb, and the complete eVOLVE Hybrid Wheel, including backbone, foam, and composite coating, weighs 19.2 lb.
On-vehicle fuel economy testing was done to EPA standard SAE J2263 by third-party testing facility Roush Emissions Laboratory, which does the same EPA drive cycles for automotive OEMs. The backbone showed some improvement over the production wheel's fuel efficiency. "But it was less of a difference: increases of 0.1 MPG city and 0.5 MPG highway," said Ardern. Using the complete eVOLVE wheel, city improvement was 0.4 MPG, and highway, 1.1 MPG.
Weight reduction alone isn't enough to achieve those results. The other main factor is the eVOLVE wheel's improved aerodynamics. Lacks performed wind tunnel testing of several hybrid wheel designs at third-party aerodynamics testing facility Aerodyn, a NASCAR lab. Lacks then selected the best performing wheel design as the eVOLVE Hybrid Wheel for further testing, Ardern told us.
Compared to the Ford Focus production wheel, in static and rotating aerodynamics testing done to EPA standard SAE J2264 the winning eVOLVE wheel design had an overall vehicle drag coefficient improvement of nine counts. "The reduction of aero drag as well as a reduction in aero horsepower both contribute to the optimized aerodynamic profile, and ultimately to fuel economy performance," said Ardern.
Rigby5, I've asked the company to address some of the issues raised in the comments here. Meanwhile, regarding holes, it's my understanding that these were in fact reduced in this wheel in part by the plastic fill and in part by the redesign. Also, this is a cutaway diagram, so much of the apparent " holes" on the right are not actually there in the finished wheel.
Ah, I see...well as always you are on the cutting edge of coverage, Ann. I should have known! :) In all seriousness, I do like the way designers are thinking outside of the box (or in this case, the power train) to come up with new ways to be more fuel efficient and economical.
While I can see that wheels can be made lighter and save gas, this does not seem like such a serious attempt. To reduce drag as much as possible, the wheel should really have no holes or ridges at all. In fact instead of a Moon, the wheel should be dished in order to smoothen linear air flow. Brake cooling should be air from below the car being ducted behind the wheel. In fact, the whole bottom of the car should be smooth, totally unlike what they do now.
So I can't really take this article that seriously, because obviously car makers and buyers really don't care. Otherwise they would have addressed these more glaring issues. Instead, the main factor for wheels must be cosmetic, with wheels having larger and larger openings these days, when they really should have no openings at all. The trouble is the customers are ignorant and the makers don't want to educate them.
And what I would really like to see is a comparison with all plastic wheels, such as fiberglass or graphite composite.
As Lacks said in the story, it's not just lighter weight, but also better aerodynamics that result in the 1.1 MPG improvement, as shown by the third-party tests.
I don't believe you know enough about wheel aerodynamics to make that statement. I don't believe that Ford couldn't make that same wheel out of aluminum. There are certainly wheels that are even more aerodynamic. Despite their claims car companies are not really interested in aerodynamics otherwise they would make them aerodynamic. Cars today are still far worse drag wise than the cars like the Jaray in the 1930's. Car companies are intrested in making profits these days not selling transportation.
This new wheel design looks like it keeps the same flaw that most aluminum wheels carry, which is that they corrode and develop rim leaks. That may not be a problem in south cal, but here in Michigan there are tons of salt dumped at the first hint of snow, and it is far worse then the navy salt-spray test could dream of being. So wheel with a good plastic in the seal area would be an improvement indeed. I really find it hard to believe that the streamlining gives a 1.1MPG improvement, or even a 1.1% improvement, unless it is being compared to the most non-aerodynamic design made.
One other question is about how the plastic portion holds up with the fairly common problem of disk brakes binding and getting really hot. That happens a bit with some Chrysler product vehicles, I have found. They knew about that problem in 1976, they have not solved it by 2005. Reduced it some, but not solved.
This new wheel design looks like it keeps the same flaw that most aluminum wheels carry, which is that they corrode and develop rim leaks. That may not be a problem in south cal, but here in Michigan there are tons of salt dumped at the first hint of snow, and it is far worse then the navy salt-spray test could dream of being. So wheel with a good plastic in the seal area would be an improvement indeed. I really find it hard to believe that the streamlining gives a 1.1MPG improvement, or even a 1.1% improvement, unless it is being compared to the most non-aerodynamic design made.
One other question is about how the plastic portion holds up with the fairly common problem of disk brakes binding and getting really hot. That happens a bit with some Chrysler product vehicles, I have found. They knew about that problem in 1976, they have not solved it by 2005. Reduced it some, but not solved.
Not only is remote start a silly accessory, it is a source that delivers 100% on pollution, since the car warming up driverless for half an hour, or even just 15 minutes is just burning fuel delivering no travel value at all. All the warmup time the engine really needs is the time that it takes me to fasten my seatbelt after starting the engine.
The whole point is the 1.1 MPG saved. There are no other wheels that can do that, so a monetary cost savings comparing this wheel to others that can't save 1.1 MPG wouldn't be very useful.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
Engineers at the University of California, San Diego are designing a robotic arm that takes inspiration from the loose, flexible, yet very strong structure of the armored plates on a seahorse's tail.
Researchers at the Missouri University of Science & Technology have designed a new nanoscale material that can transmit light faster than the 186,000 miles per second it usually takes to travel through air.
It has often been said that as California goes, so goes the nation. This spring, the state's wind power is setting energy generation records and solar energy generation is expected to rise sharply during the second half of 2013.
The latest model of Liquid Robotics' Wave Glider autonomous, unmanned marine vehicle (UMV), the SV3, is reportedly the world's first hybrid wave- and solar-power-propelled unmanned ocean robot.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
8 
