Get the right drivers! That's all it takes to remove the screws. Any tech worth his salt knows that.
Getting permission has nothing to do with it, skill and experience does. As I've stated in prior posts, are you going to find and program a proprietary chip? Are they going to sell you the programmed proprietary chip that failed?
I didn't sidestep you car thing, I ignored it. The same thing applies to them, if they use hardware then make sure that you have the correct drivers.
The hard-to-remove screws aren't to keep 'most' people out, they are intended to keep virtually everyoneout. Those manufacturers wouldn't care if it were Story Musgrave trying to repair his unit; they just don't want him inside.
And as soon as those hard-to-find screwdriver bits aren't so hard to find, the manufacturers will come out with another screw head type from their bag of duplicity.
As for enumerating the serviceable components inside, unless Apple has changed something in its licensing, the entire iPhone andthe components inside, every one of them, belong to the owner who might want to attempta repair. No permission required.
Defense of any such overprotectionism belongs in the cow pastures with what I refer to as trans-tertiary detritus.
I did note that jeffbiss tried to almost completely sidestep the car comparison. Cars which, at least on myplanet, have electronics, electrical system, mechanicals and an engine diagnostic jack which does not require FCC certification to use.
Do you suppose that the car manufacturers should change that jack type, or eliminate it completely, because some people capable of popping the hood aren't deemed capable (by the manufacturer) of using the code scanner?
If Bob Pease were still with us, this screw fiasco might well have inspired him to write a What's All This Screwjob Stuff? column.
You're just too much dude! The problem isn't that certain hardware is used, it's that you don't have the right tool to remove them. There's no conspiracy as far as I can tell. I bet that the vast majority of people who would take their thingy apart would end up finding nothing to repair.
So here's my challenge to you: provide us a parts list of repair parts that the ordinary person can buy and install. I'm also willing to bet that most people couldn't remove and install SMDs without destroying something. These things are not cars, nor are their innards machined parts.
I was ready to stop my iPhone fastener comments until I looked at the comments again and saw the 2012-02-14 4:40:05 PM post by jeffbiss.
How would he like his car hood similarly bolted shut with fasteners requiring new or hard-to-find tools that were as much trouble to acquire as the 'Pentalobular screw' bits or driver bits for other oddball fasteners?
How would he like being forced to have his car towed to the dealer or have that dealer come to him just because he needed something as simple as a jump start, but the car maker didn't deem him 'capable' of performing such a complex task?
If the owner of one of those handheld devices wants to attempt a repair on it, he should not be restricted by the duplicitous tactics of companies that seem to feel that they are the divine arbiter of everyone's & anyone's capabilities.
It's time to shelve that ultra-anal overprotectiveness and get on with living normal lives, unfettered by contrived annoyances.
Good story on fixing the phone, Leigh. My daughter forgot to take her iPod out of her pocket and it went through the washer and dryer. After that it didn't work. Somebody suggested putting it in the freezer. We did. The next day it was fine. I don't know what principles were involved in that solution.
Hah. My wife dropped her 3GS in the toilet. Because I was exceeding jealous of her phone I decided to fix it for myself. I pulled it completly apart. Replaced the battery. Scrubbed off the electrochemical corrosion. Got everything working except the camera. The phone is still working fine 12 months later.
Go Android !... Apple will do what Apple did in the 1980s that led to their first episode of demise; they will be come so incredibly exclusive and expensive that the Android Market will overcome them with it's many, many open opportuniites and selections.
Just a short comment on " The screw that Apple is using is similar to a Torx -- except that the points have a rounder shape, and the screw has five points instead of six."
The Torx screw has six rounded lobes (unlike the Allen head that has six flat lobes, actually an hexagon ).
Thus the difference of the Apple screws is five vs. six lobes not the roundness of the lobes. Another difference that may exist (I don't know) is that their mean diameter may be half way between the standard Torx diameters.
By the way for the "I gotta open this rascal " DIYs: For small Torx or Pentalobes screws, a jeweler's flat screw driver of the proper width is sufficient to turn them. Grinding the flat screw driver to the proper width is all it takes for the tightest of the very small screws. For larger bolts it is a different story..
I completely agree with your post. I have fixed an iPhone after successfully accessing the wealth of "how-to" information (mostly on Youtube) and purchasing the very inexpensive parts and tools. I will say you'd better have small hands and big dexterity (and/or a lot of patience) to manipulate tiny ribbon cables, connecters, etc. I'm guessing the rapidly shrinking world of electronics will soon render home repair an impossibility - the iPod Nano is just the beginning! :)
Truchard will be presented the award at the 2014 Golden Mousetrap Awards ceremony during the co-located events Pacific Design & Manufacturing, MD&M West, WestPack, PLASTEC West, Electronics West, ATX West, and AeroCon.
Robots that walk have come a long way from simple barebones walking machines or pairs of legs without an upper body and head. Much of the research these days focuses on making more humanoid robots. But they are not all created equal.
The IEEE Computer Society has named the top 10 trends for 2014. You can expect the convergence of cloud computing and mobile devices, advances in health care data and devices, as well as privacy issues in social media to make the headlines. And 3D printing came out of nowhere to make a big splash.
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This discussion will examine what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.