The CSA's Rex rover has a robotic arm that simulates collecting Martian rock and soil samples. It travels at 4cm/sec (1.57inch/sec). On its six aluminum or rubber wheels, the rover can navigate over obstacles up to 15cm (5.9 inches) high and climb slopes of up to 10 degrees. Rex weighs 140kg (308.64 pounds) and measures 152 x 142 x 76cm (59.84 x 55.9 x 29.92 inches). It can carry up to 30kg (66.13 pounds) of science payloads. In 2010, the CSA jointly field tested the rover with NASA at the Flagstaff Meteor Crater in Arizona. (Source: Canadian Space Agency)
Ann, this is interesting, but does the CSA plan to deploy these. I recently saw a show on PBS which went into some detaill about the Curiosity rover. This is a large vehicle. One thing that was interesting was the Mars Exploration Science Rover. Your caption states that the rover is designed to collect samples to bring back to earth. As far as I know, this is a very expensive proposition. The Curiosity rover has the lab built in so that it can analyze the samples in place.
Lou, no decisions have yet been made on what will be deployed where. These are prototypes, so the CSA is still working out the details and trying out different approaches to similar goals.
No offense to anyone but half the stuff I see in here are not going to survive space a minute in. especially that "ruggedized computer" in image ten. I can see holes the size of quarters on it that are not sealed in any way. Take it from some one that has worked on materials that actually go to space pin size cracks that require a 10X magnifying glass to see are a problem if your insulation material is not sufficient. One more thing, those connectors just don't look space worthy. Really Ethernet? Custom sealed connectors rated for space might do the trick. Generally speaking off the shelf connectors that are rated for that environment will be cheaper than to design your own too so good rule of thumb don't try this at home.
I looked critically at the critical note about figure number ten. It states the rugged processor box wouldn't last a minute in space, from "one who knows" But the legend states the box is space rated by NASA, ESA and Nippon SA. Who is kidding whom?
Ann--Excellent post. Do you know if there is available information that would tell us what "on-board" diagnostic packages exist to analyze soil, air for methane, test for water, etc etc? Is there a "standard" schedule of experiments given for probes of this type; i.e. lunar, Mars, etc? I have taken a look at the NASA web site and don't see any specifics. (Maybe missed them.) This would be very interesting to know. Again, excellent post.
Ervin. Have to agree with you on this one. I think the mechanical drive concepts are OK and fairly well thought out but lift off and re-entry are definitely tough on components and other equipment. I worked in the aerospace industry (Titan II Missile) some years ago and "survival" was the key word. Generally, mission critical components and systems had redundancy. It was amazing to me how many launches were successful due to the redundant systems after the primary systems failed. I definitely enjoyed Ann's post and it's very interesting to see what's in the works relative to probes that might be used.
When has a prototype ever been a viable product, ready for production/use? I think what's shown here is a good first step as we think about space colonization.
Nice to see that the CSA has other projects besides the arm that they are known for. This is quite a variety of concepts. I'm assuming they are platforms to test different instruments/approaches/missions rather than a "family" of rovers geared toward a specific mission.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Two new introductions in the world of motion drives for automation are moving toward use of standard Ethernet communications, eliminating the use of custom hardware.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
