Packaging robots have been designed to replace human labor, albeit with superhuman strength, agility, and speed. The range of movement, strength, and speed allow these machines to lift entire pallets onto trucks or pick up individual muffins hot out of the oven.
These robots were on display at PackExpo in Las Vegas last month. The entire tradeshow floor was alive with robotic movement. The robots were amazingly agile, surprisingly strong, and unexpectedly quiet.
This is the new manufacturing workforce. These machines are so efficient, they have reduced the importance of cheap labor as a factor in whether a plant is built in China or Ohio. While they reduce the manual workforce, they come with a small army of engineers. For the new engineer they are especially attractive, since running these robots can be done through simulation -- much like playing a video game.
Click on the image below to start the slideshow:
Here’s the claw end of a robot arm. ABB’s FlexGripper can be adjusted to pick up a wide range of items, large or small. (Source: ABB)
Rob, you slide show brought back memories, and not all good ones. Several years ago, I received a call from Bendix Automotive, their break pad division. I was asked to look at designing a robotic system to move brake pads from one conveyor line to another line for the purpose of baking. I used a "gripper" for that purpose BUT, this was during the mid-80s and long before the technology was fully developed. The forces were either too strong, thus breaking the pads or too light, dropping the pads during movement from one line to the other. It was a bear of a project.
It amazes me that devices such as shown in you slides can pick up 15,000 eggs per hour with ease and probably minimal damage. Shows us how far the technology has come.
Greg--very important point. I have two clients who have "fought the good fight" relative to process producing carpal tunnel syndrome for workers. The work accomplished is repetitive, high-speed, and extremely tiring. One client rotates his employees in this work cell every two hours to alleviate stress to wrists and shoulders. For the other client, the injuries were so numerous he finally decided to use a specially designed robotic system. This system was welcomed by the employees who became operators of the system and not hands-on workers within the cell. Prevention of injuries and cost of medical care are uppermost in the minds of most CEOs and certainly most CFOs.
Thanks for the info and video, Jim E. I was quite improssed at PackExpo by the safety features of the robots. You could put your hand in the path of the robot and it would stop instantly. Now gearing down, jut an instant stop. Most robot producers are touting higher levels of safety.
As a robot programmer with my previous company, I got to learn a bit about robotics. (Well, I still fool with them here, but only in maintenance aspects usually.)
The ABB FlexPicker is really amazing. Watching the youtube video of it picking up widgets off of a conveyor and putting them onto another conveyor in an endless cycle at amazingly high speed is really mesmerizing to watch.
The end tooling / gripper is usually one of the limiting factors in robotics use. Some items just don't pick up well with robots. One of the most incredible grippers to see is a "Jamming Phase Transition" gripper. It's basically a balloon filled with coffee grounds, and the balloon can have a vacuum applied. The gripper is placed against an item and a vacuum applied, which makes the device rigid, which conforms to what it was pressed against. You really have to see this to believe it, and here's a video: https://www.youtube.com/watch?v=ZKOI_lVDPpw
I haven't seen any industrial applications of this technology yet, but I hope it will eventually happen.
As for the human-safe robots, the Baxter seems more like a toy without the ability to reach pre-programmed points with accuracy. The Universal Robotics devices seem more like industrial robots. I played with a UR-5 at a trade-show and was impressed with it. I tested it running into my arm and it was a bizarre to me considering that I'm used to working with giant robots which would crush me. The reach and payload capacity of their two models aren't good enough for any of my applications yet, but I'd love to get one in my plant somehow.
MyDesign, I think robots really help in reducing the power of labor to determine everything in where stuff is built. If logistics costs play a bigger role than labor, it's natural that manufacturing moves closer to markets. A side benefit would be energy savings and environmental gains.
Good point, Mydesign. It does look like companies are putting more emphasis on packing. And while the robots reduce the need for manual labor, they do employ engineers. They also reduce the differential between labor costs in Asia and the rest of the world. Thus, logistics costs may trump labor as the expense to watch -- that helps fuel the trend toward buiulding plants close to markets.
Are you being paid enough? Do you want a better job? According to a recent survey Manpower released just before Engineers Week, employers and engineers don't see eye-to-eye about the state of US engineers' skills and experience.
Two issues have been the bane of the plastics industry for as long as one can remember: The ban on plastic grocery bags and whether the use of bisphenol A (BPA) in plastics such as polycarbonate and PVC is harmful to humans.
One expects to see outlandish apparel at major global fashion events, but New York Fashion Week may have outdone itself, and set a new bar for Paris and Milan, when it put an Ebola jumpsuit in the spotlight.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.