A German student has designed an energy harvester that derives energy from electromagnetic fields in the air to recharge small batteries and appliances. Dennis Siegel, who is studying digital media at the University of the Arts in Bremen, Germany, outlines the design of the harvester on his website.
As he explains it:
The omnipresence of electromagnetic fields is implied just by simple current flow. We are surrounded by electromagnetic fields, which we are producing for information transfer or as a byproduct. Many of those fields are very capacitive and can be harvested with coils and high frequency diodes.
Dennis Siegel has created an energy harvester that can be used to harvest ambient energy from electromagnetic fields in the air, such as those present near power lines, plugged-in electric appliances, or mobile phones. Siegel is studying digital design at the University of Bremen. (Source: Dennis Siegel)
To take advantage of this capability, Siegel built harvesting devices that can tap into several electromagnetic fields and harvest energy, which is then stored in a typical battery. As he continues on his website:
So you can for example gain redundant energy from the power supply of a coffee machine, a cell phone, or an overhead wire by holding the harvester directly into the electromagnetic field whose strength is indicated by a LED on the top of the harvester.
With the energy harvested, it’s possible to charge a small battery in just a day depending on the size of the electromagnetic field. "The system is meant to be an option for granting access to already existing but unheeded energy sources," Siegel writes. "By exploring these sources it can create a new awareness of the invisible electromagnetic spaces while giving them a spatial dimension."
If you think about it, Siegel’s concept is not such a complex one. Electronic devices, even when switched off, emit electricity if they’re plugged in, as do any other devices that use electricity to run.
Indeed, his website features photos of people holding up the device in various places where ambient energy would be present, such as in close proximity to a coffee machine, a power line, and someone speaking on a mobile device.
Siegel describes two types of harvesters that can be developed -- a small one for lower frequencies below 100Hz that are found in general mains (50/60Hz, 16,7Hz), and a bigger one that can be used to harvest energy from both lower and higher frequencies, like radio broadcast (~100MHz), GSM (900/1800MHz), or Bluetooth and WLAN (2,4GHz).
Energy harvesting is emerging as one way to provide alternative energy for small, battery-powered devices. Options for harvesting are being explored for medical devices, small home appliances like smoke alarms, and a number of other applications.
Companies also are investing products that promote energy harvesting, such as Texas Instruments’ new low-power converter and a low-power circuit from Dutch startup Anagear that harvests energy to provide more efficient power management.
Debera, I think I may have missed your comment earlier, as I just replied to another user that I agree with you all who are commenting that this isn't really "stealing." I think it's a creative reuse of what's already out there and I think that this type of technology should be promoted.
Thank you for your comment, charles000. I, too, thought a lot of the concern about stealing the energy was unwarranted. As you say, many of these devices are just showing the potential for taking advantagae of the energy that's out there and available, so it's not really so different.
Anne, You are absolutely correct i too dont agree with the idea of stealing energy because this is not stealing energy we are just utilizing the wasted or excess energy as we know all these electromegnatic devices continue to emit energy even when not working .Harvesting energy from air is an excellent idea we can use these devices at airports where radar and communication devices emit energy to harvest and power wireless sensors that could detect nuclear material .
"Stealing" is not the same as harvesting. There was no intent of malice here, but rather to indicate a potential mechanism for energy recycling, from whatever source may be available. There are currently (no pun intended) myriad devices and techniques for "energy scavenging" technology already being used or in development. Why should this be considered any differently?
You're welcome, notarboca. I'm quite frankly surprised by the level of comment I've received on this one. You never know as a writer what is going to provoke a response, and there are opinions and angles to this story that people have posed that I have never thought of. Thanks for reading.
If you disrupt the broadcast RF or decrease the coverage area (e.g. by using a very large antenna or array), they might have a case against you. But it would be much harder for the provider to detect the loss, if you are a distance from the transmitter.
However, it is impractical to use RF energy transmitted at a distance. Transmitted EM waves follow the Inverse Square Law (http://en.wikipedia.org/wiki/Inverse-square_law) which states that the power density of an electromagnetic wave is proportional to the inverse of the square of the distance from a point source.
The power is reduced in proportion to the square of the distance to the source. i.e. - If you double the distance to a source, you will only have 1/4 of the power (you lose 3/4 of the power).
Power is monitored at substations or below, so there are not millions of killowatts being sensed. If he was stealing enough to power his entire house, they would detect the loss.
The first electric Co-ops were formed in rural areas like Oklahoma when neighbors would pay to run power lines between themselves and a nearby distribution line. The electric companies didn't want to power scattered rural homes because they would never get a return on the line investment. Even when the small communities ran their own lines, the power companies didn't want to hook them up and become liable for their distribution.
To force the issue, the co-ops would put poles next to the electric company's line for a distance and parasitically power their homes.
The EM field of conductors is NOT wasted energy and any EE should know that. It is simply the result of passing current through the conductor. Sheilding is not an option when considering the massive currents involved in power distribution.
You can use these devices all you want behind YOUR power meter where you get charged for the energy you consume. But using power you are not being charged for, plus causing additional distribution loses to the provider (find your own EE to explain); is increasing the provider's costs and decreasing the available energy to legitimate customers. IT IS THEFT! period!
Now I like this idea, shehan. If they don't like the idea of other people doing it, they should set up harvesters themselves...that way no precious energy is lost. We could perhaps solve the energy crisis this way. What a good idea.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New disc magnet motors fit into the design trend of stepping up to closed loop performance while maintaining the cost advantage of stepper motor technology.
At the Design News webinar on June 27, learn all about aluminum extrusion: designing the right shape so it costs the least, is simplest to manufacture, and best fits the application's structural requirements.
A new battery design, which replaces lithium with abundant and low-cost elemental sulfur, is still in its nascent stages but shows real promise for giving batteries more energy potential.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
