Field technician: Where does the grey wire from terminal 21 go?
Engineer: Grey? That wire should be light blue.
Field technician: All the wires I see are grey.
This is what happens when the talented but willful production team takes engineering directives as suggestions. Decisions regarding component selection are informed by specifications, regulations, physical laws, and personal preference. Regardless of how a decision was arrived at (fortune cookies, dice rolling, asking the janitor, etc.), it is not the place of production to second-guess engineering. If it was, then they would be the ones in a windowless office under flickering fluorescents, surrounded by productivity-increasing bland grey furnishings.
I am not talking about problems reported back to engineering for correction. I am talking about laborers thinking they will use a solenoid in place of the one you specified, because it looks similar and has the same voltage rating, and then not telling anybody.
Excuses like "I ran out of blue wire," "It's almost identical," and my favorite, "That's not how we used to do it," are not valid excuses. I can't even think of a valid excuse. In this particular case, a multimillion-dollar fire suppression system was to be installed throughout a manufacturing facility. This location routinely bursts into flames, they use kerosene as a lubricant. Fire breaks out, CO2 floods the area, workers have just enough time to escape certain suffocation. The control panels for this facility were being repaired and upgraded, when some questions arose. As they gave the opening exchange, above, they had replaced control panels wiring with some grey wire that looked "like the same stuff." After an argument over the wire, the engineer's demands won out. The project was on hold until the proper wire was obtained.
How do we assist the field tech or customer when documentation does not match the physical design in the field? An adulterated design which may later require the ministrations of a technician because production took liberties during construction.
@TJ McDermott: Being "colorblind" doesn't mean being unable to see colors; it just means that it's more difficult to differentiate between certain colors.
I have deuteranopia, which is one of the most common forms of colorblindness. While most people have three types of color receptors (red, green, and blue), my eyes only have receptors for red and blue. Since I don't have specialized receptors for intermediate-wavelength colors, they don't appear as distinct to me as they probably do to you. For example, the colors gold, light orange, and light green all look pretty similar to me.
This site has some good pictures that illustrate how colorblind people see things.
You're definitely right about labelling wires. Whenever I have to deal with color-coded wires (red and green; blue is not a problem for me), I usually have a non-colorblind person tell me what color the wires are. Then I attach small pieces of tape labelled "RED" or "GREEN."
I suppose that if someone wanted to make my life more difficult, they could either lie about the wire colors, or else switch my pieces of tape when I'm not looking. Thankfully, I've managed to get along well enough with my co-workers that it's never happened.
Interestingly enough, a small percentage of women are said to be tetrachromats, meaning that they have four types of color receptors instead of just three. That would make them better able to distinguish between colors than regular people.
The gist of the article is about unapproved substitions, and I agree 100% with the author. An unapproved substituion is one reason for the KC Hyatt skybridge collapse we discussed several months ago.
The specifics of the article bring up a slightly different question. Should color be a differentiator? I know fully well the color standards for wiring, use it in my control panel designs, even agree that such a standard makes a ton of sense.
But what about color blindness? Somewhere between 5%-7% of the male population has some form of color blindness. For those, labeling and positioning are the only way to differentiate wires or controls.
Excuses only come up when critical thinking is absent. I'm sure we all have stories about others but how many are willing to admit that we've done it too?
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
6 
