HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
Blogs
Blog

# Want to Generate Energy? Go Fly a Kite

View Comments: Newest First|Oldest First|Threaded View
<<  <  Page 2/3  >  >>
User Rank
Gold
Re: End of the Track
11/13/2012 6:09:03 PM
NO RATINGS
Am I missing something? How could the generator car possibly "loop back" when the kites are pulling in a vector that probably won't vary by more than 45 degrees?  Assuming a long narrow oval track at 90 degrees to the wind, on the straight legs of the oval the kites would only be providing a portion of the total force anyway: moving the generator first to the left, say, on the up wind straight leg, then following the wind direction through the first curve, then the kite would have to tack to the right, pulling the generator to the right on the downwind straight leg, then it would get to the next curve, somehow proceed against the kite force and midway through the curve the kite needs to reverse tack to the left, the generator still working against the kite to get back to the straight leg.  If this works they've discovered perpetual motion.

User Rank
Gold
Re: Kite Control
11/13/2012 4:01:18 PM
NO RATINGS

Yes you need 4 lines for control.  While it looks interesting it has many problems too which I han't seen fixed yet by any proposal I've seen.

The [problems of wear, line entanglment, power transfer,  height, aircraft make these hard to get right.  I doubt anything above 1000' would be practical and even 50' problematic.

Cloth isn't going to get it as they wouldn't last long and hard kites have their own problems.

A better idea is the old 3blade wind turbine I believe until someone can show me a viable kite system that can last.

I should say here I've sailed and design, build high speed sailboats plus wind generators and have never firgured out how the 2 can be combined after 1,000's of hrs trying.

User Rank
Gold
economically feasible
11/13/2012 1:03:30 PM
NO RATINGS
Unlike solar farms or windmills which are inherently difficult to look at or follow with the eyes, advertisers could use these kites to place their logos on truly unobstructed billboards, and not cut down any trees in the process.  So capitalism could serve environmentalism for a change.  And vice versus.

Of course, the kites would have to fly in a public area, but those are the small details.  : )

User Rank
Gold
Kite Control
11/13/2012 10:59:42 AM
NO RATINGS
A close view of the picture shows four lines going to the kite.  This might imply that that 4 lines are needed for strength and or redundancy.  However, it also implies that the kite would be capable of being directionally controlled (tacking) allowing it to fly in directions not directly downwind.  Nothing mandates that a track mounted generator can't store enough power to propel itself while tacking crosswind down a track perpendicular to the wind for the brief period needed to navigate the half loop at the end of an oval track.  Then there's the design study needed to show if a figure 8 track (allowing more downwind travel) of a given distance would provide more net power than an oval track with a given diameter at the ends.

User Rank
Gold
Re: End of the Track
11/13/2012 9:43:17 AM
NO RATINGS
I think the only solution for aircraft concerns would be to ban aircraft from the area entirely.  This is especially true since in the US, aviation is moving away from flight paths to routes decided by pilots through GPS tracking.

This is not unprecedented.  There are many areas off limits to aircraft already.

It does remind me a bit of barrage balloons during Word War II I read about.

User Rank
Blogger
Re: End of the Track
11/13/2012 4:19:27 AM
NO RATINGS
Excellent points about aircraft concerns. Lights could be one option; however, I'm sure as this system continues to get tested this will be addressed. One easy solution would be to try to put them in areas where there aren't often low-flying craft. Staying far away from airports is an obvious solution to that.

User Rank
Platinum
Re: End of the Track
11/12/2012 8:09:17 PM
I didn't want to say anything from an aviation standpoint, because that's something I'm a little biased on.  Since the door's been opened, I think it's outrageously dangerous to have a kite above 1000' AGL.  Yes, there are antennas that reach that high with nice, bright beacons, and one can assume that the kite would be as well lit, but the problem with a kite is that you have no way of knowing where the aluminum shredding tether is going to be.  There was a story similar to this before, and I likened the tethered, airborne windmill to a WWII era barrage balloon, and certainly, the effect to a passing aircraft would be similar.

User Rank
Blogger
Re: End of the Track
11/12/2012 7:31:02 PM
NO RATINGS
I wonder if they've thought about potential aircraft collisions. In Illinois, where I live, it's very easy to spot wind turbines at night because wind farms typically have synchronized red lights that blink on and off at night. Could they do the same with kites?

User Rank
Blogger
Re: End of the Track
11/12/2012 5:08:09 PM
NO RATINGS
Liz, thanks for covering this--what fun, how elegant, and I like the lower environmental impact of the technology. While most wind turbines don't go as high, the one we wrote about here
http://www.designnews.com/document.asp?doc_id=243636
is designed to eventually achieve over 1,000 feet in altitude.

User Rank
Platinum
Re: Airborne Technology
11/12/2012 3:47:10 PM
NO RATINGS
It might be very similiar to model rocketry protocol - waivers sometimes have to be filed and approved with the FAA and flight patterns have to meet certain criteria. That would probably be a good way to deal with air traffic. We wouldn't want a model rocket crashing through one of those kites!

<<  <  Page 2/3  >  >>
 Partner Zone
More Blogs
Both traditional automation companies and startups are developing technologies to improve processes on the factory floor, while smart sensors and other IoT-related technologies are improving how products are handled during transport and across the supply chain.
Remote monitoring now looks beyond the individual motor or conveyor and instead views the process from end to end.
At ARM TechCon 2016, CEO Simon Segars will discuss how he sees billions of devices scaling to trillions as IoT applications proliferate. We know it’s happening. How do we prepare?
Highly regarded engineer and physicist Ransom Stephens speaks with Design News about his extensive science and engineering background, the serious yet funny study of neuroscience, and how one primes their brain for innovation.
It's your turn to cast your vote for one of these 12 finalists to win the ARM TechCon Reader's Choice Award for the most innovative product of the past year.
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 10 - 14, Embedded System Design Techniques™: Getting Started Developing Professional Embedded Software
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course September 27-29:
Sponsored by 3M
Twitter Feed
Like Us on Facebook

### Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service