HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Blog

Electrohydraulic Control for Farm Vehicles

NO RATINGS
Page 1 / 3 Next >
View Comments: Newest First|Oldest First|Threaded View
Jack Rupert, PE
User Rank
Platinum
Re: How did they do the rear drive?
Jack Rupert, PE   10/22/2012 12:21:14 PM
NO RATINGS
Given the concerns about weight and sinking into the mud, I was surprised with the relatively thin tires.  Being in the mining industry for a number of years, the first thing that was done when needing "high flotation" was to increase the width of the tracks in that case.  I wonder why a wider tire wasn't implemented here - or is that a farming requirement due to the width of the furrows?

Ann R. Thryft
User Rank
Blogger
Re: Impressive makeover
Ann R. Thryft   10/15/2012 6:39:44 PM
NO RATINGS
Wow, Chuck, that's impressive. How tall was the silo, do you remember?

Rob Spiegel
User Rank
Blogger
Re: Impressive makeover
Rob Spiegel   10/12/2012 3:33:57 PM
NO RATINGS
Chuck, the silo story is another impressive story about hydraulics used on the farm. Are these issolated instances of inventive solutions -- or, do some of these solutions get commercialized. I would guess the need goes beyond these individual instances.

kf2qd
User Rank
Platinum
Design Requirements
kf2qd   10/12/2012 11:29:33 AM
NO RATINGS
A spray rig needs to be able to make extremely tight turns at the end of the field. Any normal steering axle that is also driven would be limited by the angle of the wheels because of the universal joints. Some 4 wheel drive tractors use a right angle drive at the top of the steering kingpin through a hollow kingpin down to the wheel. Problem for an application like this with extremely low production would be that the cost of machining and fabrication of the special gears and such would be prohibitive.

The rear wheels can be driven by a set of gears, or belts, or chains without a problem, but the ability to turn makes the front axle more difficult.


Don't know if you have ever spent any time on any farm equiptment, but it is normal that ag equiptment is able to have a turn radius that is little longer than the length of the vehicle. A normal 4 wheel drive truck has a turning radius larger than a comparable 2 wheel drive truck. And most 4 wheel drive axles, when engaged, require an even larger turn radius.

Consider that a field will have rows spaced 30"(or 24"). The wheels may be spaced at 120" to go down the center of the rows. That puts 4(or 5) rows under the tractor. There will be 3 rows outboard on each side.  So I get to the end of the row and pick up the implement at the end of the row and as soon as it is clear of the crop I do a hard turn to clear the fence at the edge of the field (and I don't allow any extra rom because if I make the turn around area 4 foot bigger I lose a couple acres at each end of the field) and then I make a sharp turn into the sixth row over and head to the other end of the field. If I have to wrestle with a vehicle with a large turn radius I will waste a lot of time trying to get out of the currrent row and into the next. With 3500 acres to work I don't have a lot of time to spend maneuvering, as getting the current spray on the field may be a time sensitive operation.

burntpuppy
User Rank
Silver
Re: How did they do the rear drive?
burntpuppy   10/12/2012 10:41:15 AM
NO RATINGS
Google portal axles, they could have done the same thing on the front (steer) axle but it is harder to get the strength and a good turning radius.

 The Hummer, Unimog and some Volvo trucks use portal axles.

Jim_E
User Rank
Platinum
How did they do the rear drive?
Jim_E   10/12/2012 10:25:38 AM
NO RATINGS
I'm curious how they did the rear drive system on the machine. 

The picture shows "crop clearance" for the rear wheels, but the article states "The normal transmission output is used to drive the rear wheels."  I'm used to seeing a traditional differential rear end, but I obviously dont' see a "pumpkin" hanging down low. 

Did they install some sort of bevel gear adapters on the end of the normal differential, with an equivalent set down on the wheel centers?

 

Greg M. Jung
User Rank
Platinum
Resourceful
Greg M. Jung   10/11/2012 9:23:54 PM
NO RATINGS
Great example of solving a problem using mainly off-the-shelf components and some key innovation in the remaining areas.  Way to think outside the 'box'.

Charles Murray
User Rank
Blogger
Re: Impressive makeover
Charles Murray   10/11/2012 7:39:16 PM
NO RATINGS
I agree it's impressive, Rob. The ag industry is known for innovative use of hydraulics and this is a perfect example. A few years ago (okay, maybe it was 25 years ago), I did a story for Design News about a farmer who developed an electrohyadulic actuation system to tip over a silo, lay it on its side, and lift it onto a flat bed trailer.

Rob Spiegel
User Rank
Blogger
Impressive makeover
Rob Spiegel   10/11/2012 12:55:44 PM
NO RATINGS
This is quite an impressive makeover. I would guess there are plenty of situations where this electrohydraulic vehicle would solve problems on farms. I wonder if these folks are planning to commercialize their vehicle.

Partner Zone
More Blogs
The damage to Sony from the cyber attack seems to have been heightened by failure to follow two basic security rules.
Reshoring is picking up steam, but it's not outpacing the overall continuing growth in outsourcing.
Here's a variety of views into the complex production processes at Santa's factory. Happy Holidays!
The Beam Store from Suitable Technologies is managed by remote workers from places as diverse as New York and Sydney, Australia. Employees attend to store visitors through Beam Smart Presence Systems (SPSs) from the company. The systems combine mobility and video conferencing and allow people to communicate directly from a remote location via a screen as well as move around as if they are actually in the room.
Thanks to 3D printing, some custom-made prosthetic limbs, and a Lego set, one lucky dog and a tortoise has learned new tricks.
Design News Webinar Series
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
11/19/2014 11:00 a.m. California / 2:00 p.m. New York
11/6/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jan 12 - 16, Programmable Logic - How do they do that?
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service