There was definitely something in the air -- nanoparticles, perhaps? -- at the recent Seventh Annual Livingston Nanotechnology Conference. There was an amazing energy of optimism and opportunity as nearly 30 nanotechnology and advanced manufacturing startups offered presentations about their companies to an audience of investors.
On Dec. 7, I had the pleasure of presenting to this esteemed audience (mainly men, I might add, ahem) on behalf of MEMS Industry Group (MIG). I had a ball, and I plan to come back every year.
Scott Livingston was the MC for the day’s event, and he did a stellar job of introducing/networking/commenting/digressing/having a good time to promote his investment philosophy of taking back Wall Street and giving it back to the people (the 99 percent people). Not to get all Occupy Wall Street on you, but Scott has an important message on how the US investment community does not invest in and reward advanced manufacturing. (Yes, it will invest in Groupon and Zynga, but not real job-creating, wealth-generating industries like MEMS, save a few examples like InvenSense.)
The reality is that the US has a competitive advantage in advanced manufacturing in nano- and, to some extent, microtechnology. The time is now, and we can’t afford to blow it.
So that’s where I fit in. I gave a brief introduction to MIG (MEMS Industry Group) and the MEMS market, and then Scott and I did a little back-and-forth interview about the opportunities in MEMS. And he even asked me to list some MEMS startups that folks should check out and invest in. (Some of you owe me big time.) We also talked about the recent InvenSense IPO.
So what was my main message? I lauded the fact that MEMS is in the mainstream. In other words, I said, "MEMS is frickin' everywhere." Well, not quite. What I did say is that the potential for MEMS is huge, and that MEMS has the opportunity to be "frickin’ everywhere," and that investors should jump on board the MEMS train and help fund this potential (and make some money, too).
@Rob - thanks for the comment. I think I answered the first part of your question in my other responses. But for your second question, MEMS is truly an international and very diversified industry that spans a spectrum of markets and applications. Therefore you'll find MEMS companies and companies in the MEMS supply chain everywhere. That being said, there are some hubs of MEMS around the world. In the US, they are in Silicon Valley (mainly) followed by Boston; as well as in Texas (Dallas/Austin); AZ (Phoenix/Tempe); PA (Pittsburgh - my hometown); to name a few... Internationally, Europe is a hot-bed for MEMS and that is why we are hosting our first MEMS Executive Congress Europe on 20.March in Zurich - www.memscongress.com for more info - we are featuring ONLY EU speakers and keynotes at this senior-level event.
@Dave - YES - MEMS is big in consumer - that's why CEA invited us (MEMS Industry Group - MIG) to host the first-ever MEMS TechZone at CES this week: http://www.memsindustrygroup.org/i4a/pages/index.cfm?pageID=4057
and you can also see the aforementioned MEMS in Machine for a bigger list.
@Charles - I am pretty sure that those MEMS accelerometers are in nearly EVERY laptop now - they were originally in IBM laptops (when IBM made laptops!) but now b/c of the pricepoint I am pretty sure you'll see it in most. Now laptops have other MEMS inside of them, including MEMS microphones. You may want to check out the MEMS Industry Group (MIG) list of "MEMS in the machine" to see where else you can find MEMS:
@Alex Your post is making me blush. Thank you for the kind words and yes, I will try to be more bold in my exclamations of how amazingly frickin' awesome MEMS is; just like in "the Graduate" when the old guy gave advice to Dustin Hoffman, instead of "Plastics" one should invest in MEMS; it truly will be everywhere. See you at CES!
I recall that MEMS-based accelerometers we're supposed to get big in laptops, as a means of shutting down a hard drive when the computer falls. Any sense of what percentage of laptops now use this technology?
Author Karen Lightman is being too modest. She's a MEMS heavyweight herself, as Managing Director of the MEMS Industry Group. I refer you to her bio, here. The MEMS events sponsored by the group, which will take place the week of Jan. 8 at CES in Las Vegas, are listed here.
I have a couple questions about the trajectory of MEMS. First, in what industries is MEMS getting traction. I would imagine health care equipment would be huge. Are there other industries that are going full steam?
I know that the Silicon Valley companies are still attractive to venture capitalists. To some extent Silicon Valley has the benefit of a physical center. People living in the same neighborhood get to know each other. Is there a geographical center for MEMS that helps boost investment and adoption?
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New disc magnet motors fit into the design trend of stepping up to closed loop performance while maintaining the cost advantage of stepper motor technology.
At the Design News webinar on June 27, learn all about aluminum extrusion: designing the right shape so it costs the least, is simplest to manufacture, and best fits the application's structural requirements.
A new battery design, which replaces lithium with abundant and low-cost elemental sulfur, is still in its nascent stages but shows real promise for giving batteries more energy potential.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
