HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Sherlock Ohms
CNC Control in Electrically Noisy Environments
8/14/2012

Return to Article

View Comments: Newest First|Oldest First|Threaded View
<<  <  Page 2/2
ttemple
User Rank
Platinum
Re: WHy not proper shielding?
ttemple   8/14/2012 1:34:23 PM
NO RATINGS
While it doesn't explicitly state it in the article, it appears that the encoders in question have single ended outputs.  It appears that the extenders convert the signals to differential mode, which is much more noise tolerant.  Shielding is a good idea, but with single ended signals I doubt it would have been enough if there is serious high frequency switching noise all around.

kf2qd
User Rank
Platinum
WHy not proper shielding?
kf2qd   8/14/2012 11:30:30 AM
NO RATINGS
Having built and serviced CNC plasma cutting machines, proper shielding of cables does wonders. The comercial products we used all had shielding built into the harness to keep the noise out. And the shields were always grounded at 1 end only., and in some cases where the design was older and more sensitive they actually had 2 shields, insulated from each other and each one grounded at opposite ends of the cable.

Also - effort should be made to seperate the motor and encoder cables. Often just having them shielded and a few inches apart is sufficient.

GlennA
User Rank
Gold
ground loop ?
GlennA   8/14/2012 11:07:31 AM
NO RATINGS
You mention using shielded cables.  Did you ground only one end of the cable shield ?  I have seen installations with both ends of the cable shield connected to ground, which makes ground loops a concern.

naperlou
User Rank
Blogger
Shorter signal path
naperlou   8/14/2012 9:02:24 AM
NO RATINGS
I was wondering, as I was reading the article, why you did not look at shortening the signal path.  I can think of reasons, but I am wondering what the situation is in this case.

<<  <  Page 2/2
Partner Zone
More Blogs from Sherlock Ohms
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Design News Webinar Series
11/19/2014 11:00 a.m. California / 2:00 p.m. New York
11/6/2014 11:00 a.m. California / 2:00 p.m. New York
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Dec 1 - 5, An Introduction to Embedded Software Architecture and Design
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service