HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Sherlock Ohms

Glue & Sealant Gunk Up the Line

NO RATINGS
View Comments: Newest First|Oldest First|Threaded View
<<  <  Page 3/3
Nancy Golden
User Rank
Platinum
Re: They can't both be bad
Nancy Golden   10/24/2012 12:32:00 PM
NO RATINGS
I agree, Rob - since part swapping is usually a quick way to verify if a part is operating correctly. I would also have been tempted to call the cable good and look further for a different problem. I have done it in the past (just grabbing another part out of a parts bin) and after wasting time verifying everything else was okay, I would return to the part I had called "good" and finally figure out that while it was not the obvious answer, the replacement was also bad. Glenn did a great job going to a KNOWN good cable to make his call - a great tip for anyone involved in troubleshooting!

Rob Spiegel
User Rank
Blogger
Re: They can't both be bad
Rob Spiegel   10/24/2012 11:00:11 AM
NO RATINGS
Good point Naperlou. Glenn will likely weigh in on this. If the cable was new but defective, you would get a powerful bias that the cable wasn't the problem.

naperlou
User Rank
Blogger
Re: They can't both be bad
naperlou   10/24/2012 10:35:01 AM
NO RATINGS
Glenn, that was good work.  I always found that there are often several different failure modes and it is important to isolate them.  The problem with the second cable is a difficult one.  I wonder if that cable was considered "new" or if it was a spare from another unit.

Rob Spiegel
User Rank
Blogger
They can't both be bad
Rob Spiegel   10/24/2012 5:56:05 AM
NO RATINGS
Good detective work, Glenn. When the replacement cable was also bad, it would have been easy to determine that the cable wasn't the problem.

<<  <  Page 3/3
Partner Zone
More Blogs from Sherlock Ohms
Building a prototype of a car is a tough way to find the optimal balance between efficiency and comfort. the Sherlocks at Ford are finding the balance using simulation.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Design News Webinar Series
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
11/19/2014 11:00 a.m. California / 2:00 p.m. New York
11/6/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jan 12 - 16, Programmable Logic - How do they do that?
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service